INFINITI QX56 2011 Factory Service Manual

INT-32
< REMOVAL AND INSTALLATION >
HEADLINING
 Personal lamp assembly. Refer to INL-77, "Removal and Installation".
 Rear ventilator grille assembly. Refer to VTL-13, "
REAR VENTILATOR GRILLE : Removal and Installa-
tion".
 Headlining harness.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Be careful not to bend h eadlining when installing.
 First install metal clips of map lamp assembly and cl ips of the rear end of headlining for positioning.
Revision: 2010 May2011 QX56

LUGGAGE FLOOR TRIMINT-33
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
LUGGAGE FLOOR TRIM
Exploded ViewINFOID:0000000006220258
1. Rear pillar finisher LH 2. Luggage upper finisher LH 3. Luggage side lower finisher LH
4. Back pillar garnish LH 5. Rope hook 6. Clip
7. Luggage lower board LH 8. Luggage floor finisher LH 9. Luggage floor bracket
JMJIA4308ZZ
Revision: 2010 May2011 QX56

INT-34
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
*: Reclining switch (22) is also installed on luggage side lower finisher LH (3).
LUGGAGE FLOOR REAR BOARD
LUGGAGE FLOOR REAR BOARD : Removal and InstallationINFOID:0000000006220259
REMOVAL
1. Open luggage floor board center (1).
2. Remove both bolts shown by the arrows in the figure, and then
remove luggage floor board center.
3. Remove luggage floor finishers (LH/RH). 1. Remove bolts shown by the arrows in the figure.
2. Disengage luggage floor finisher (1) fixing pawl and clip
using a remover tool (A), and then remove luggage side fin-
isher.
4. Remove both luggage floor rear boards. 1. Fold down the third seat forward.
2. Remove rope hook (1) mounting bolt using a socket wrench
(A), and then remove rope hook.
10. Luggage floor board center 11. Tool box 12. Luggage rear plate
13. Luggage rear plate mask 14. Child anchor cover 15. Luggage floor finisher RH
16. Luggage lower board RH 17. Fold down switch 18. Back pillar garnish RH
19. Luggage side lower finisher RH 20. Luggage upper finisher RH 21. Rear pillar finisher RH
22. Reclining switch*
: Clip
: Pawl
JMJIA4027ZZ
: Clip
: Pawl
JMJIA4028ZZ
JMJIA4029ZZ
Revision: 2010 May2011 QX56

LUGGAGE FLOOR TRIMINT-35
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
3. Disengage luggage floor board RH (1) fixing pawls and clips, and then remove luggage side finisher.
4. Disengage luggage floor board LH (2) fixing pawls and clips,
and then remove luggage side finisher.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Visually check the clips and pawls for deformation and damage during installation. Replace with new
ones if necessary.
 When installing luggage floor rear board, check that clips and pawls are securely fitted in body panel
holes, and press them in.
LUGGAGE REAR PLATE
LUGGAGE REAR PLATE : Removal and InstallationINFOID:0000000006220260
REMOVAL
1. Open luggage floor board center.
2. Remove luggage floor finishers (LH and RH).
1. Remove nuts shown by the arrows in the figure.
2. Disengage luggage floor finisher (1) fixing clip and pawl
using a remover tool (A), and then remove luggage side fin-
isher.
3. Disengage luggage rear plate (1) fixing clips and pawls using a remover tool (A), and then remove luggage rear plate.
4. Remove luggage rear plate mask from luggage rear plate.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Visually check the clips and pawls for deformation and damage during installation. Replace with new
ones if necessary.
 When installing luggage rear plate, check that cl ips and pawls are securely fitted in body panel
holes, and press them in.
: Clip
: Pawl
JMJIA4030ZZ
: Clip
: Pawl
JMJIA4028ZZ
: Clip
: Pawl
JMJIA4041ZZ
Revision: 2010 May2011 QX56

INT-36
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
LUGGAGE SIDE LOWER FINISHER
LUGGAGE SIDE LOWER FINISHER : Removal and InstallationINFOID:0000000006220261
REMOVAL
1. Lift up the seat base, tilt seatback fo rward, and fold down second seat forward.
2. Remove second seat belt anchor. Refer to SB-13, "
SEAT BELT RETRACTOR : Removal and Installation".
3. Remove third seat. Refer to SE-138, "
Removal and Installation".
4. Remove third seat belt anchor. Refer to SB-19, "
SEAT BELT RETRACTOR : Removal and Installation".
5. Remove luggage floor board center and both luggage lower boards. Refer to INT-34, "
LUGGAGE FLOOR
REAR BOARD : Removal and Installation".
6. Remove luggage rear plate. Refer to INT-35, "
LUGGAGE REAR PLATE : Removal and Installation".
7. Remove rope hook (1) mounting bolt using a socket wrench (A), and then remove rope hook.
8. Disengage luggage side lower finisher fixing clip (1) using a small flat-bladed screwdriver (A) as shown by the arrow in the
figure, and then remove clip.
9. Remove luggage side lower finisher. 1. Disengage luggage side lower finisher (1) fixing clips andpawls.
2. Disconnect luggage room power socket harness connector (LH side only).
3. Disconnect fold down switch harness connector (RH side only).
4. Disconnect reclining switch harness connector (LH and RH).
5. Remove luggage side lower finisher.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
JMJIA4043ZZ
JMJIA4042ZZ
: Clip
: Pawl
JMJIA4044ZZ
Revision: 2010 May2011 QX56

LUGGAGE FLOOR TRIMINT-37
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
 Visually check the clips and pawls for deformation and damage during installation. Replace with new
ones if necessary.
 When installing luggage side lo wer finisher, check that clips and pawls are securely fitted in body
panel holes, and press them in.
REAR PILLAR FINISHER
REAR PILLAR FINISHER : Removal and InstallationINFOID:0000000006220262
REMOVAL
1. Remove luggage side lower finisher. INT-36, "LUGGAGE SIDE LOWER FINISHER : Removal and Instal-
lation".
2. Disengage lower side of rear pillar finisher fixing clip.
3. Pull rear pillar upper garnish (1) from inside passenger room, disengage rear pillar upper garnish upper side fixing pawl as shown in the following figure, and then remove rear pillar upper garnish from body
panel (2).
CAUTION:
Be careful not to apply excessive force when removing rear pillar finisher. Otherwise, pawl may be
damaged and fragments may drop in body panel holes on body.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Replace rear pillar finisher wi th a new part after removal. Never reuse rear pillar finisher.
 Visually check the clip and pawl for deformation an d damage during installation. Replace with new
ones if necessary.
 When installing rear pillar finisher, check that cl ip and pawl are securely fitted in body panel holes,
and press them in.
BACK PILLAR GARNISH
BACK PILLAR GARNISH : Removal and InstallationINFOID:0000000006220263
REMOVAL
1. Remove luggage side lower finisher. INT-36, "LUGGAGE SIDE LOWER FINISHER : Removal and Instal-
lation".
2. Remove cap of back door finisher side (LH), and then remove stud ball. Refer to DLK-247, "
BACK DOOR
SUPPORT ROD : Removal and Installation" (LH side only).
3. Disengage back pillar garnish (1) fixing clips and pawl using a remover tool (A), and then remove back pillar garnish.
JMJIA1176ZZ
: Clip
: Pawl
JMJIA4045ZZ
Revision: 2010 May2011 QX56

INT-38
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Visually check the clips and pawl for deformation and damage during installation. Replace with new
ones if necessary.
 When installing back pillar garnis h, check that clips and pawl are securely fitted in body panel holes,
and press them in.
LUGGAGE SIDE UPPER FINISHER
LUGGAGE SIDE UPPER FINISHER : Removal and InstallationINFOID:0000000006220264
REMOVAL
1. Remove luggage side lower finisher. Refer to INT-36, "LUGGAGE SIDE LOWER FINISHER : Removal
and Installation".
2. Remove rear pillar finisher. Refer to INT-37, "
REAR PILLAR FINISHER : Removal and Installation".
3. Remove back pillar garnish. Refer to INT-37, "
BACK PILLAR GARNISH : Removal and Installation".
4. Remove luggage side upper finisher. 1. Remove mounting bolts (1).
2. Disengage luggage side upper finisher (2) fixing clips usinga remover tool (A), and then remove luggage side upper fin-
isher (3).
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Visually check the clips for deformation and dama ge during installation. Replace with new ones if
necessary.
 When installing luggage side uppe r finisher, check that clips are securely fitted in body panel holes,
and press them in.
: Clip
JMJIA4046ZZ
Revision: 2010 May2011 QX56

BACK DOOR TRIMINT-39
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
BACK DOOR TRIM
Exploded ViewINFOID:0000000006220265
Removal and InstallationINFOID:0000000006220266
REMOVAL
1. Fully open back door.
1. Back door finisher lower 2. Auto back door switch finisher 3. Pull handle
4. Back door assembly 5. Back door finisher side RH 6. Back door finisher upper
7. Back door finisher side LH 8. Cap 9. Lamp mask
10. Emergency handle mask : Clip
: Pawl
: Metal clip
JMJIA4421ZZ
Revision: 2010 May2011 QX56

INT-40
< REMOVAL AND INSTALLATION >
BACK DOOR TRIM
2. Disengage pull handle finisher (1) fixing pawls using a removertool (A), and then remove pull handle finisher.
3. Disengage auto back door switch finisher (1) fixing pawls using a remover tool (A), and then disconnect auto back door switch
harness connector.
4. Remove back door finisher inner lower (1) fixing clips (A).
5. Remove the back door finisher inner lower. 1. Disengage back door finisher inner lower (1) fixing clips and pawls using a remover tool (A).
NOTE:
Start disengaging from the position where pa wls are located as shown in the figure.
: Pawl
JMJIA4048ZZ
: Pawl
JMJIA4049ZZ
JMJIA4047ZZ
: Clip
: Pawl
JMJIA4050ZZ
Revision: 2010 May2011 QX56

BACK DOOR TRIMINT-41
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
K L
M A
B
INT
N
O P
2. Remove back door finisher inner lower.
6. Disengage back door finisher side (1) fixing metal clips using a remover tool (A), and then remove back door finisher side.
7. Disengage back door finisher upper (1) fixing metal clips using a remover tool (A), and then remove back door finisher upper.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
 Visually check the clips, pawls and metal clips for deformation and damage during installation.
Replace with new ones if necessary.
 When installing back door trims, check that clips, pawls, and metal clips are securely fitted in body
panel holes, and press them in.
: Metal clip
JMJIA4052ZZ
: Metal clip
JMJIA4051ZZ
Revision: 2010 May2011 QX56