Bolt JAGUAR XFR 2010 1.G Workshop Manual
Page 971 of 3039
9.
10.
11.
12.
CAUTION: Discard the bolts.
NOTES:
Discard the gasket.
Make sure that the position of the spacers is noted
before removal of the manifold. www.JagDocs.com
Page 973 of 3039
3. NOTE: If a new cylinder head is installed use the
special tools in the illustration.
Special Tool(s): 303-1444-02
4. CAUTION: Make sure that new bolts are installed.
NOTE: Install the spacers in the noted position.
Torque: 10 Nm
5. Remove the special tool.
6. CAUTION: Make sure that new bolts are installed.
NOTE: Install the spacers in the noted position.
Torque: 10 Nm
Page 974 of 3039
7.
8.
9.
10. Torque: 18 Nm
Torque: 100 Nm
WARNING: Make sure that a new bolt is installed.
NOTE: Some variation in the illustrations may occur,
but the essential information is always correct.
Torque: 35 Nm
Page 978 of 3039
5.
6.
All vehicles
7.
CAUTION: Discard the bolt.
Torque: 35 Nm
Torque: 100 Nm
Torque: 12 Nm
Page 979 of 3039
8.
9.
10.
11. Torque: 48 Nm
CAUTIONS:
Discard the bolts.
LH illustration shown, RH is similar.
NOTES:
Discard the gasket.
Make sure that the position of the spacers is noted
before removal of the manifold.
Page 981 of 3039
3. CAUTION: LH illustration shown, RH is similar.
NOTE: If a new cylinder head is installed use the
special tools in the illustration.
Install the special tool.
Special Tool(s): 303-1444-02
4. CAUTIONS:
Make sure that new bolts are installed.
LH illustration shown, RH is similar.
NOTE: Install the spacers in the noted position.
Torque: 10 Nm
5. CAUTION: LH illustration shown, RH is similar.
Remove the special tool.
6. CAUTIONS:
Make sure that new bolts are installed.
LH illustration shown, RH is similar.
NOTE: Install the spacers in the noted position.
Torque: 10 Nm www.JagDocs.com
Page 983 of 3039
11. Torque: 48 Nm
Right-hand drive vehicles
12.
13.
CAUTION: Discard the bolt.
Torque: 35 Nm
Torque: 100 Nm
Page 985 of 3039
Engine - V8 S/C 5.0L Petrol - Flexplate
Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. CAUTION: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
3. Refer to: Transmission - V8 5.0L Petrol/V8 S/C 5.0L Petrol (307-01B Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8
S/C 5.0L Petrol, Removal).
4. CAUTIONS:
Install all the bolts finger tight before final tightening.
The bolts can only be used 3 times, mark the bolts
with a center punch. If 2 punch marks are visible, discard
the bolts.
Make sure that no components fall off during removal.
Install the bolts in the noted position.
NOTES:
Make sure the crankshaft and flexplate mating faces
are clean before installation.
Make sure that the crankshaft is not rotated.
Tighten the retaining bolts working diagonally.
Torque:
Stage 1:45 Nm Stage 2:90°
Installation
1. To install, reverse the removal procedure.
Page 988 of 3039
Installation 9. CAUTIONS:
Make sure that these components are installed to the
noted removal position.
Install new o-ring seals
1. CAUTIONS:
Install all the bolts finger tight before final tightening.
Make sure that the area around the component is
clean and free of foreign material.
Install the new seals.
NOTE: Tighten the bolts in the indicated sequence.
To install, reverse the removal procedure.
Page 992 of 3039
Installation
1. CAUTIONS:
Use only a plastic scraper when removing the sealing
material.
Use lint free cloth.
Make sure that the mating faces are clean and free of
corrosion and foreign material.
Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G)
to the areas shown, and tighten the bolts within 7
minutes.
Apply a bead of sealant, 2.5 mm diameter, to the
area indicated.
2. NOTE: Tighten the bolts in the sequence shown.
Torque: 12 Nm
3. Refer to: Engine Oil Level Sensor (303-14D Electronic Engine Controls - V8 S/C 5.0L Petrol, Removal and Installation).