JAGUAR XFR 2010 1.G Workshop Manual

3. CAUTION: LH illustration shown, RH is similar.


NOTE: If a new cylinder head is installed use the
special tools in the illustration.
Install the special tool.

Special Tool(s): 303-1444-02







4. CAUTIONS:


Make sure that new bolts are installed.
LH illustration shown, RH is similar.
NOTE: Install the spacers in the noted position.

Torque: 10 Nm





5. CAUTION: LH illustration shown, RH is similar.
Remove the special tool.














6. CAUTIONS:


Make sure that new bolts are installed.
LH illustration shown, RH is similar.
NOTE: Install the spacers in the noted position.
Torque: 10 Nm www.JagDocs.com

7.
















8.
9.
10. CAUTION: LH illustration shown, RH is similar.

Torque: 18 Nm


















































Torque: 12 Nm

11. Torque: 48 Nm













Right-hand drive vehicles

12.
13.
CAUTION: Discard the bolt.

Torque: 35 Nm













Torque: 100 Nm

Petrol/V8 S/C 5.0L Petrol, Removal and Installation).

16. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

Engine - V8 S/C 5.0L Petrol - Flexplate
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. CAUTION: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Transmission - V8 5.0L Petrol/V8 S/C 5.0L Petrol (307-01B Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8
S/C 5.0L Petrol, Removal).

4. CAUTIONS:


Install all the bolts finger tight before final tightening.


The bolts can only be used 3 times, mark the bolts
with a center punch. If 2 punch marks are visible, discard
the bolts.
Make sure that no components fall off during removal.
Install the bolts in the noted position.

NOTES:


Make sure the crankshaft and flexplate mating faces
are clean before installation.


Make sure that the crankshaft is not rotated.


Tighten the retaining bolts working diagonally.
Torque:
Stage 1:45 Nm Stage 2:90°
Installation

1. To install, reverse the removal procedure.

Engine - V8 S/C 5.0L Petrol - Oil Cooler
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 19-Nov-2013

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Cooling System Partial Draining, Filling and Bleeding - V8 S/C 5.0L Petrol (303-03C Engine Cooling - V8 5.0L Petrol/V8 S/C 5.0L Petrol, General Procedures).

4. Refer to: Supercharger (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).

5.
6. www.JagDocs.com

7. CAUTIONS:


Be prepared to collect escaping oil.


Be prepared to collect escaping coolant.

Torque: 13 Nm









8. CAUTION: Make sure that these components are
installed to the noted removal position.


NOTE: Install a new gasket.

Installation 9. CAUTIONS:


Make sure that these components are installed to the
noted removal position.


Install new o-ring seals

1. CAUTIONS:


Install all the bolts finger tight before final tightening.


Make sure that the area around the component is
clean and free of foreign material.


Install the new seals.


NOTE: Tighten the bolts in the indicated sequence.
To install, reverse the removal procedure.

Engine - V8 S/C 5.0L Petrol - Oil Filter Element
Removal and Installation

Removal Published: 11-May-2011


NOTE: Some variation in the illustrations may occur, but the essential information is always correct.

1. Refer to: Engine Cover - V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-05 Interior Trim and Ornamentation, Removal and Installation).

2.
Allow the engine oil to drain from the oil filter
element housing for two minutes.















3.
4.

3. Check and top-up the engine oil.

4. Start and run the engine.

5. Refer to: Engine Cover - V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-05 Interior Trim and Ornamentation, Removal and Installation). Installation