LAND ROVER FREELANDER 2001 Workshop Manual

SECURITY
86-4-4 REPAIRS
4.Release door aperture seals to release
headlining.
5.Release 3 studs securing rear edge of
headlining to roof panel.
6.Remove 4 screws securing headlining to 'B'
posts.
7.Release 2 studs securing sides of headlining to
body.
8.Lower front edge of headlining.
9.Release sun roof seal.
10.Remove 2 screws from volumetric sensor.
11.Disconnect multiplug from volumetric sensor
and remove.Refit
1.Position volumetric sensor and connect
multiplug.
2.Fit sensor and secure with screws.
3.Fit headlining to 'B' posts and secure with
screws.
4.Secure headlining behind rear vent rubbers.
5.Fit headlining rear finisher.
6.Fit door aperture seals.
7.Fit headlining to sun roof seal.
8.Position roof lamp and connect multiplug.
9.Fit roof lamp and secure with screws.
10.Fit lens to roof lamp.

SECURITY
REPAIRS 86-4-5
Module (ECU) - volumetric - alarm
system - 5 door - without sunroof
$% 86.77.29
Remove
1.Remove LH rear quarter upper trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - upper
- 5 door.
2.Remove LH 'A' post upper finisher.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
3.Release front and rear LH door seals.
4.Remove screw covers and screws from both
LH grab handles and remove grab handles.
5.Remove LH sun visor.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Sun visor.6.Remove trim stud securing forward edge of
headlining.
7.Remove 2 trim studs securing centre of
headlining.

SECURITY
86-4-6 REPAIRS
8. Up to 04MY: Remove lens from front interior
lamp.
9. Up to 04MY: Remove 2 Torx screws securing
front interior lamp to body.
10. Up to 04MY: Release front interior lamp from
headlining, disconnect multiplug and remove
lamp.
11. From 04MY: Working from lamp forward edge,
release front interior lamp from headlining,
disconnect multiplug and remove lamp.12.Release LH 'B/C' post upper finisher.
13.Carefully lower headlining to gain access to
volumetric sensor.
14.Disconnect multiplug from volumetric sensor.
15.Remove 2 screws and remove sensor.

SECURITY
REPAIRS 86-4-7
Refit
1.Fit volumetric sensor and secure with screws.
2.Connect multiplug to sensor.
3.Raise headlining and secure with trim studs.
4. Up to 04MY: Position front interior lamp and
connect multiplug.
5. Up to 04MY: Fit Torx bolts securing interior
lamp and tighten to 6 Nm (4.4 lbf.ft).
6. Up to 04MY: Fit lens to front interior lamp.
7. From 04MY: Position front interior lamp and
connect multiplug.
8. From 04MY: Fit and secure front interior lamp
to headlining.
9.Position 'B/C' post upper finisher and secure
with clips.
10.Fit sun visor.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Sun visor.
11.Fit grab handles, tighten screws and fit screw
covers.
12.Fit 'A' post upper finisher.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
13.Fit rear quarter upper trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - upper
- 5 door.
14.Secure front and rear door seals.
Module (ECU) - volumetric - alarm
system - 5 door - with sunroof
$% 86.77.29
Remove
1.Release front and rear door aperture seals.
2.Remove 'A' post upper finishers.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
3.Remove screw covers, remove 6 screws
securing front and both rear grab handles and
remove grab handles.
4.Remove grab handle blanking plugs.

SECURITY
86-4-8 REPAIRS
5.Release and remove sun roof finisher.
6.Remove both sun visors.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Sun visor.
7.Remove trim stud securing forward edge of
headlining.8. Up to 04MY: Remove lens from front interior
lamp.
9. Up to 04MY: Remove 2 Torx screws securing
front interior lamp to body.
10. Up to 04MY: Release front interior lamp from
headlining, disconnect multiplug and remove
lamp.
11. From 04MY: Working from lamp forward edge,
release front interior lamp from headlining,
disconnect multiplug and remove lamp.

SECURITY
REPAIRS 86-4-9
12.Remove 2 trim studs securing centre of
headlining.
13.Release 8 clips securing both 'B/C' post upper
finishers and pull finishers clear of headlining.
14.Carefully lower headlining to gain access to
volumetric sensor.15.Disconnect multiplug from volumetric sensor.
16.Remove 2 screws securing volumetric sensor
and remove sensor.
Refit
1.Fit volumetric sensor and secure with screws.
2.Connect multiplug to sensor.
3.Secure the headlining with trim studs.
4.Position 'B/C' post upper finisher and secure
with clips.
5.Fit sun visors.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Sun visor.
6.Fit 'A' post upper finishers.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
7.Fit grab handles, tighten screws and fit screw
covers.
8.Fit grab handle blanking plugs.
9. Up to 04MY: Position front interior lamp and
connect multiplug.
10. Up to 04MY: Fit Torx bolts securing interior
lamp and tighten to 6 Nm (4.4 lbf.ft).
11. Up to 04MY: Fit lens to front interior lamp.
12. From 04MY: Position front interior lamp and
connect multiplug.
13. From 04MY: Fit and secure front interior lamp
to headlining.
14.Position and secure sun roof finisher.
15.Secure front and rear door seals.

SECURITY
86-4-10 REPAIRS
Receiver - alarm system
$% 86.77.31
Remove
1.Remove instrument cowl.

+ INSTRUMENTS, REPAIRS, Cowl -
instrument - up to 04MY.
Up to 04MY illustrated.
2.Remove 4 screws and remove instrument
panel upper cover.
3.Disconnect multiplug and remove alarm
receiver from instrument pack.
Refit
1.Fit alarm receiver and connect multiplug.
2.Fit instrument panel upper cover and secure
with screws.
3.Fit instrument cowl.

+ INSTRUMENTS, REPAIRS, Cowl -
instrument - up to 04MY.
Coil - passive immobilisation - alarm
system
$% 86.77.35
Remove
1.Remove steering column nacelle.

+ STEERING, REPAIRS, Nacelle -
column.
2.Release passive coil from steering lock.
3.Collect illumination ring.
4.Disconnect multiplug and remove passive coil.
Refit
1.Fit illumination ring.
2.Fit passive coil and connect multiplug.
3.Fit steering column nacelle.

+ STEERING, REPAIRS, Nacelle -
column.

WINDOWS
REPAIRS 86-5-1
WINDOWS REPAIRS
Motor & control unit - front door - 3 door
$% 86.25.01
Remove
1.Remove upper plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - upper - 3 door.
2.Remove lower plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - lower - 3 door.
3.Remove 4 Torx screws securing door stiffener,
release bowden cable from clip and remove
door stiffener.
4.Disconnect multiplug from door glass motor.
5.Loosen 2 screws clamping control unit to glass
and release glass from clamps.
6.Remove 5 screws securing control unit to door.
7.Manoeuvre motor and control unit out from
door aperture.Refit
1.Position motor and control unit in door aperture
and locate to glass.
CAUTION: It is very important when fitting
the control unit that the cable with the anti-
rattle sleeve is next to the trim casing and
the motor cable next to the glass.
2.Secure control unit to door with screws.
3.Tighten clamps securing control unit to glass, to
9 Nm (7 lbf.ft).
4.Connect multiplug to door glass motor.
5.Position door stiffener, fit and tighten Torx
screws to 9 Nm (7 lbf.ft).
6.Secure cable in door stiffener clip.
7.Fit lower plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - lower - 3 door.
8.Fit upper plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - lower - 3 door.

WINDOWS
86-5-2 REPAIRS
Motor & control unit - front door - 5 door
$% 86.25.01
Remove
1.Remove front door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - 5 door.
2.Disconnect multiplug from door glass motor.
3.Loosen 2 screws clamping control unit to glass.
4.Release cable from door clip.
5.Remove 5 screws securing control unit to door.
6.Release cable from door clip and manoeuvre
motor and control unit out from door aperture.
Refit
1.Position motor and control unit in door aperture
and locate to glass.
CAUTION: It is very important when fitting
the control unit that the cable with the anti-
rattle sleeve is next to the trim casing and
the motor cable next to the glass.
2.Fit and tighten screws securing control unit to
door.
3.Secure cable in door clip.
4.Tighten clamps securing control unit to glass, to
9 Nm (7 lbf.ft).
5.Connect multiplug to door glass motor.
6.Fit front door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - 5 door.
Switch - master window - 5 door - from
04MY
$% 86.25.08
The procedure to remove the window lift and door
panic lock switches is similar to the one shown
below.
Remove
1.Carefully release window lift switch pack from
door trim casing.
2.Disconnect 3 multiplugs from window lift switch
pack and remove switch pack.
NOTE: Do not carry out further dismantling if
component is removed for access only.
3.Carefully release and remove window lift switch
pack from bezel.
Refit
1.Fit window lift switch pack to bezel.
2.Position switch pack, connect multiplugs and
secure switch pack to trim casing.
M76 4698

WINDOWS
REPAIRS 86-5-3
Relay - control - tail door glass
$% 86.25.45
Remove
1.Remove RH rear quarter lower trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 3 door.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
2.Remove tail door glass control relay.Refit
1.Fit tail door glass control relay.
2.Fit RH rear quarter lower casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 3 door.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.