NISSAN ALMERA TINO 2001 Service Repair Manual

Component Parts and Harness Connector
Location
NLEL0441
NEL781
System DescriptionNLEL0442UNIFIED CONTROL METERNLEL0442S01+Speedometer, odo/trip meter, tachometer, fuel gauge and water temperature gauge are controlled totally
by control unit built-in combination meter.
+Digital meter is adopted for odo/trip meter.*
*The record of the odo meter is kept even if the battery cable is disconnected. The record of the trip meter
is erased when the battery cable is disconnected.
+Odo/trip meter segment can be checked in diagnosis mode.
+Meter/gauge can be checked in diagnosis mode.
HOW TO CHANGE THE DISPLAY FOR ODO/TRIP METERNLEL0442S02
SEL394X
NOTE:
Turn ignition switch to the ªONº position to operate odo/trip meter.
METERS AND GAUGES
Component Parts and Harness Connector Location
EL-130

POWER SUPPLY AND GROUND CIRCUITNLEL0442S03Power is supplied at all times
+through 10A fuse [No. 12, located in the fuse block (J/B)]
+to combination meter terminal 8.
With the ignition switch in the ON or START position, power is supplied
+through 10A fuse [No. 30, located in the fuse block (J/B)]
+to combination meter terminal 9.
Ground is supplied
+through body grounds M28 and M48
+to combination meter terminal 7.
WATER TEMPERATURE GAUGENLEL0442S04The water temperature gauge indicates the engine coolant temperature. The reading on the gauge is based
on the resistance of the thermal transmitter.
As the temperature of the coolant increases, the resistance of the thermal transmitter decreases. A variable
ground is supplied to terminal 5 of the combination meter for the water temperature gauge. The needle on the
gauge moves from ªCº to ªHº.
TACHOMETERNLEL0442S05The tachometer indicates engine speed in revolutions per minute (rpm).
The tachometer is regulated by a signal
+from terminal 32 (Gasoline engine models) or 439 (Diesel engine models) of the ECM
+to combination meter terminal 19 for the tachometer.
FUEL GAUGENLEL0442S06The fuel gauge indicates the approximate fuel level in the fuel tank.
The fuel gauge is regulated by a variable ground signal supplied
+from body grounds M28 and M48
+through terminals 4 and 7 of combination meter,
+through terminal 1 of the fuel level sensor unit and
+through terminal 4 of the fuel level sensor unit
+to combination meter terminal 3 for the fuel gauge.
SPEEDOMETERNLEL0442S07The combination meter provides a voltage signal to the vehicle speed sensor for the speedometer.
The voltage is supplied
+from combination meter terminal 18 for the speedometer
+to terminal 1 of the vehicle speed sensor.
Ground is supplied
+from body grounds M28 and M48
+through terminals 6 and 7 of combination meter
+to terminal 2 of the vehicle speed sensor.
The speedometer converts the voltage into the vehicle speed displayed.
METERS AND GAUGES
System Description (Cont'd)
EL-131

Combination MeterNLEL0443CHECKNLEL0443S01Models with NATS security indicator on dash boardNLEL0443S0105
YEL990B
METERS AND GAUGES
Combination Meter
EL-132

Models with NATS security indicator in combination meterNLEL0443S0106
YEL488C
METERS AND GAUGES
Combination Meter (Cont'd)
EL-133

SchematicNLEL0444MODELS WITH NATS SECURITY INDICATOR ON DASH
BOARD
NLEL0444S02
YEL991B
METERS AND GAUGES
Schematic
EL-134

MODELS WITH NATS SECURITY INDICATOR IN
COMBINATION METER
NLEL0444S03
YEL489C
METERS AND GAUGES
Schematic (Cont'd)
EL-135

ConstructionNLEL0445
NEL739
METERS AND GAUGES
Construction
EL-136

Wiring Diagram Ð METER ÐNLEL0446MODELS WITH FUSE AND FUSIBLE LINK BOX E43NLEL0446S01
YEL894B
METERS AND GAUGES
Wiring Diagram Ð METER Ð
EL-137

YEL895B
METERS AND GAUGES
Wiring Diagram Ð METER Ð (Cont'd)
EL-138

MODELS WITH FUSE AND FUSIBLE LINK BOX E90NLEL0446S02
YEL419C
METERS AND GAUGES
Wiring Diagram Ð METER Ð (Cont'd)
EL-139