GEELY CK 2008 Workshop Manual

144Section 5 Front Brake AssemblyComponents
Repairing1. Remove the front wheel
2. Drain the brake fluid. Remove the brake hose
3. Remove the front brake caliper
(1) Remove the brake hose union thread from the front brake cylinder. Disconnect the hose
(2) Remove 2 installing bolts
4. Remove the front brake pad
5. Remove the front left disc caliper
6. Remove the sliding pin bootDisk Brake Wheel
Cylinder BracketSliding Pin BootInner Floating Clip PlateScrew PlugBrake Caliper
HousingInner
DamperInner Pad
Backing
PlateInner PadOuter PadOuter Pad
Backing PlateOuter
DamperOuter Floating
Clip PlateAlarm
PlateWheel
Cylinder
PistonWheel
Cylinder
Piston SealWheel
Cylinder
BootSteel Wire
Snap RingShort Pin
Set BoltShort BushingGuide Boot (II)Splash ShieldFront Ring GearRetaining
RingWheel Hub BoltFront Wheel
Hub Bearing
Wheel HubDisc

145Remove 2 boots from the brake cylinder support bracket.
7. Remove the brake cylinder guide boot
Remove the clip and boot with screwdriver.
8. Remove the bleeder screw
9. Remove the front brake piston
(1) Put a piece of soft cloth between the brake cylinder and piston.
(2) Blow the piston out from the brake cylinder with the compressed air
Notice: Be careful not to put your finger in front of the piston when blowing
the compressed air. Be careful of the splashed brake fluid
10. Remove the piston oil seal
Remove the oil seal from the brake cylinder with a screwdriver
11.Check the brake cylinder and piston
Check the cylinder wall and piston for rust and damage
12. Check the thickness of the brake pad
Measure the thickness with a ruler: Standard thickness: 10mm,
Minimum thickness: 1mm
13. Check the front brake alarm plate
Make sure the alarm plate has enough elasticity, and is not cracked
or worn. Clean all rust, dirt and foreign materials
14. Check disc thickness
Measure the disc thickness with micrometer:
Standard thickness: 11mm
Minimum thickness: 10mm

14615. Remove the front disc
16. Installation is in the reverse order of the above-mentioned procedure
Notice:
(1) The maximum lateral runout of the disc surface should be no more than 0.05mm
(Measured 10mm from the brake disc outside edge)
(2) Be careful not to install the brake cylinder guide boot in the reverse direction
(3) Make sure the cylinder and the piston oil seal are clean before installing the
piston oil seal in the brake cylinder. Apply lithium soap base glycol grease to
the piston surface. Never rotate the piston into the brake cylinder by force.
(4) Install the brake caliper to tighten the bolt torque: 85~90 N.m
(5) Replace the noise insulator when replacing the worn brake pad. Make sure the
clip plate is in normal status. Otherwise, replace the floating clip plate
(6) Make sure the brake pad and disc surface are clean. Oil or grease is not attached.
(7) Install the brake hose. Uion thread torque: 16~20N.m
(8) Bleed the air in the brake system. Check the brake system for leakage.
(9) Install the front wheel. The tire nut torque: 95~115 N.msimultaneously.floating

147Section 6 Rear BrakeComponents
Repairing1. Remove rear wheel
2. Drain the brake fluid
3. Remove the brake drum
(1) loose the parking brake handle
(2) Remove the cotter pin with a long nose pliers
(3) loose the spindle slot nut
Lower Return Spring
Oil Baffle Plate
Anchor Plate
Brake Bottom Plates
Left Cable Plate
Left Torsion Spring
Adjusting Pawl Shaft
Pin
Left Adjusting
Pawl
Left Adjusting
Plate
Brake Shoe I
Wheel Hub Bearing II
Rear Spindle Cap
Wheel Hub
Bearing I
Stop Washer
Wheel Hub
Bolt
Rear Ring Gear
Rear Brake Drum
Rear Spindle Cover
Brake Shoe I
Shoe Guide
Friction Shoe
Boot
Cup
Piston
Wheel Cylinder
Spring
Piston
BootCup
Parking Brake
Left Swing Arm
Rear Brake
Auto
Adjusting Lever
Adjusting Lever Spring
Return Spring

148(4) remove the brake drum
4. Measure brake drum inside diameter
Standard inside diameter: 180mm
Maximum inside diameter: 181mm
5. Separate the parking brake left swing arm. Loose the parking brake cable end joint
Separate the parking brake left swing arm. Remove the parking brake cable end joint with a screwdriver.
6. Remove the brake shoe I, brake shoe II
(1) using special tool, remove brake shoe positioning spring and pin
(2) remove brake shoe I and I after separating the return spring
7. Remove the rear brake automatic adjustment lever
Remove the brake adjustment lever spring and adjustment lever
8. Remove the return spring on the brake shoe
Remove the return spring from the brake shoePush

1499. Remove the parking brake lever accessory
10. Inspect shoe lining thickness
Standard thickness: 4.0mm
Minimum thickness: 1.0mm
Replace the shoe if the lining thickness is less than the minimum or seriously worn.
11.Inspect brake drum and brake shoe lining for proper contact
If the contact between brake drum and shoe lining is improper, repair the lining with a brake shoe
grinder or replace the brake shoe.
12. Check brake wheel cylinder
Check the cylinder wall, piston cup for damage
13. Install brake wheel cylinder accessory
(1) Apply lithium soap base glycol grease to 2 brake wheel cylinder cups and pistons
(2) Replace two new cups and boots
14. Install the brake wheel cylinder
Brake wheel cylinder set bolt torque: 9~13 N.m
15. Apply high temperature grease
Apply high temperature grease to the contact surface of anchor
plate hole and pin. Smear a thin layer grease to back plate.
16. Install parking brake swing arm and other accessories
17. Install brake shoe I, II
18. Install brake shoe return spring

15019. Install rear brake clearance automatic adjustment lever
20. Adjust the installing position of the brake shoe£¬install the brake drum
21. Fill the brake fluid
22. Bleed the air in the brake system
23. Check the fluid level in the reservoir
24. Check the brake fluid for leakage
25. Install the rear tire, tire nut torque: 95~115 N.m
26. Check parking brake operating handle. Check the parking brake control handle stroke and adjust if
necessary. (See parking brake system)Adjust BoltBack Plate

151Section 7 Brake LineComponents1. RF Brake Pipe Compo 2. Front Brake Hose Assembly 3. L-shaped spring Clip 4 U-shaped Clip
5. Hex Bolt Spring Washer and Flat Washer Compo 6. 5-pipe Clip 7. Brake Master Cylin-
der to Controller No.1 Brake Pipe Compo. 8. Brake Master Cylinder to Controller No.2 Brake Pipe
Set 9. HECU controller assembly 10. RR No. 1 Brake Pipe Compo. 11. Bolt12. Insu-
lator13. LF Brake Pipe Compo. 14. HECU Controller Bracket Assembly15. Hexagon
Bolt Spring Washer and Plate Washer Compo. 17. Hex Bolt Spring Washer and Flat Washer Compo.
18. LR No. 1 Brake Pipe Compo. 19. 5-Pipe Clip 20. RR Brake Pipe Compo.21.RL Brake Pipe
Compo.22. Rear brake Hose Assembly 23. Rear brake No. 3 Brake Pipe Compo.24: Single
Tube Clip25. Hexagon Bolt Spring Washer and Big Flat Washer Compo.26. Rear Brake No. 4
Brake Pipe Compo.

152Replacement1. Drain the brake fluid in the brake pipeline
2. Separate rear left, right brake pipe compo.
(1) Loose union thread. Separate the rear left brake pipe compo. and rear left No. 1 brake pipe compo.
(2) Loose union thread. Separate the rear right brake pipe compo. and rear right No. 1 brake pipe
compo.
3. Remove the rear brake pipe No 3 & 4 compo.
(1) Loose the union thread connecting the hose. Remove E-shaped clip on the pipe bracket. Separate
the brake pipe.
(2) Remove pipe No. 3 & 4 compo.
Connect RF BrakeRear RH Brake Pipe Compo.Rear LH Brake Pipe Compo. Rear LH No. 1 Brake Pipe Compo.Rear RH No. 1 Brake Pipe Compo.
C
o
n
n
e
c
t
L
F

B
r
a
k
e

1534. Remove the rear brake hose compo.
Loose the union thread that connects the rear brake hose to LR and RR brake pipe compo., remove the
E-shaped clip on the hose support bracket. Remove the rear brake hose compo.
5. Remove rear left, right brake pipe compo.
(1) Remove a dual tube clip
(2) Remove three 5-pipe clips
(3) Remove rear left, right brake pipe compo.
6. Remove front brake hose assembly
(1) Loose the union thread that connects the front brake hose to LR and RR brake pipe
(2) Remove E-shaped clip on the hose bracket
(3) Loose the union thread that connects the front brake hose to the front brake. Remove the front
brake hose assembly from the front brake
7. Remove the front left, front right brake pipe compo.
8. Remove the No. 1 & 2 brake pipe compo. which connect the brake master cylinder to HECU controller