IDX INFINITI QX4 2001 Factory Service Manual

RHA817H
DIAGNOSTIC PROCEDURENBHA0107SYMPTOM:
IA/C system does not come on.
RHA818H
Auto Amp. CheckNBHA0107S01Check power supply circuit for auto amp. with ignition switch ON.
Measure voltage across terminal Nos. 26, 27, 33 (24, 25, 33) and
body ground.
Voltmeter terminal
Voltage
(+) (þ)
26 (24)
Body ground Approx. 12V 27 (25)
33 (33)
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
SC
EL
IDX
TROUBLE DIAGNOSES
A/C System (Cont'd)
HA-73

Mode Door Motor
TROUBLE DIAGNOSIS PROCEDURE FOR MODE DOOR MOTOR (LAN)=NBHA0090SYMPTOM:
IAir outlet does not change.
IMode door motor does not operate normally.
Inspection FlowNBHA0090S01Without Navigation SystemNBHA0090S0101
SHA245F
*1: HA-25
*2: HA-66
*3: HA-44
*4: HA-45
*5: HA-129*6: HA-132
*7: HA-135
*8: HA-141
*9: STEP-BY-STEP PROCEDURE
(HA-45), see No. 13.*10: HA-78
*11: HA-81
*12: HA-66
*13: HA-65
*14: HA-139
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
SC
EL
IDX
TROUBLE DIAGNOSES
Mode Door Motor
HA-75

SYSTEM DESCRIPTION=NBHA0052Component PartsNBHA0052S01Mode door control system components are:
1) Auto amp.
2) Mode door motor (LCU)
3) In-vehicle sensor
4) Ambient sensor
5) Sunload sensor
6) Intake sensor
System OperationNBHA0052S02The auto amplifier receives data from each of the sensors. The amplifier sends air mix door and mode door
opening angle data to the air mix door motor LCU and mode door motor LCU.
The air mix door motor and mode door motor read their respective signals according to the address signal.
Opening angle indication signals received from the auto amplifier and each of the motor position sensors are
compared by the LCUs in each motor with the existing decision and opening angles. Subsequently, HOT/
COLD or DEFROST/VENT operation is selected. The new selection data is returned to the auto amplifier.
RHA870H
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
SC
EL
IDX
TROUBLE DIAGNOSES
Mode Door Motor (Cont'd)
HA-77

1 CHECK POWER SUPPLY FOR AUTO AMP. (LCU) SIDE
Do approx. 12 volts exist between auto amp. (LCU) harness terminal No. 21 and body ground?
RHA819H
NOTE:
If the result is NG or No after checking circuit continuity, repair harness or connector.
YesorNo
Ye s©GO TO 2.
No©Replace auto amp. (LCU).
2 CHECK SIGNAL FOR AUTO AMP. (LCU) SIDE
Do approx. 5.5 volts exist between auto amp. (LCU) terminals No. 16 or 14 and body ground?
RHA820H
NOTE:
If the result is NG or No after checking circuit continuity, repair harness or connector.
YesorNo
Ye s©GO TO 3.
No©Replace auto amp. (LCU).
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
SC
EL
IDX
TROUBLE DIAGNOSES
Mode Door Motor (Cont'd)
HA-79

6 CHECK MOTOR OPERATION
Disconnect and reconnect the motor connector and confirm the motor operation.
OK or NG
OK (Return to operate
normally)©Poor contacting the motor connector
NG (Does not operate
normally)©GO TO 7.
7 CHECK MODE DOOR MOTOR OPERATION
1. Disconnect the mode door motor and air mix door motor connector.
2. Reconnect the mode door motor and confirm the motor operation.
OK or NG
OK (Mode door motor
operates normally)©Replace the air mix door motor.
NG (Mode door motor
does not operate nor-
mally)©GO TO 8.
8 CHECK AIR MIX DOOR MOTOR OPERATION
1. Disconnect the mode door motor connector.
2. Reconnect the air mix door motor and confirm the air mix door motor operation.
OK or NG
OK (Air mix door motor
operates normally)©Replace mode door motor.
NG (Air mix door motor
does not operate nor-
mally)©Replace auto amp.
RHA505G
CONTROL LINKAGE ADJUSTMENTNBHA0091Mode DoorNBHA0091S011. Install mode door motor on heater unit and connect it to main
harness.
2. Set up code No. in Self-diagnosis STEP 4. Refer to HA-45.
3. Move side link by hand and hold mode door in DEF mode.
4. Attach mode door motor rod to side link rod holder.
5. Make sure mode door operates properly when changing from
code No.
toby pushing DEF switch.
VENT B/L B/L FOOT D/F DEF
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
SC
EL
IDX
TROUBLE DIAGNOSES
Mode Door Motor (Cont'd)
HA-81

With Navigation SystemNBHA0098S0102
RHA871H
*1: HA-44
*2: HA-129
*3: HA-132
*4: HA-135
*5: HA-141*6: STEP-BY-STEP PROCEDURE
(HA-45), see No. 13.
*7: HA-78
*8: HA-85
*9: HA-85*10: HA-66
*12: HA-66
*13: HA-65
*14: HA-139
*15: HA-45
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
SC
EL
IDX
TROUBLE DIAGNOSES
Air Mix Door Motor (Cont'd)
HA-83

Air Mix Door Control SpecificationNBHA0059S03
RHA137G
RHA849E
COMPONENT DESCRIPTIONNBHA0060The air mix door motor is attached to the heater unit. It rotates so
that the air mix door is opened or closed to a position set by the
auto amplifier. Motor rotation is then conveyed through a shaft and
the air mix door position is then fed back to the auto amplifier by
PBR built-in air mix door motor.
RHA504G
SHA522EA
CONTROL LINKAGE ADJUSTMENTNBHA0099Air Mix Door (Water Cock)NBHA0099S011. Install air mix door motor on heater unit and connect it to main
harness.
2. Set up code No. 41 in Self-diagnosis STEP 4. Refer to HA-44.
3. Move air mix door lever by hand and hold it in full cold posi-
tion.
4. Attach air mix door lever to rod holder.
5. Make sure air mix door operates properly when changing from
code No.
toby pushing DEF switch.
Full cold Full hot
6. Set up code No.in Self-diagnosis STEP 4.
7. Attach water cock rod to air mix door lever and secure with clip.
8. Rotate air mix door lever (CLOCKWISE completely) and hold
water cock rod and link lever in the full cold position.
9. Attach water cock rod to link lever and secure with clip (white
mark on cable housing should be centered under the retaining
clip).
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
SC
EL
IDX
TROUBLE DIAGNOSES
Air Mix Door Motor (Cont'd)
HA-85

Intake Door Motor
TROUBLE DIAGNOSIS PROCEDURE FOR INTAKE DOOR=NBHA0092SYMPTOM:
IIntake door does not change.
IIntake door motor does not operate normally.
Inspection FlowNBHA0092S01Without Navigation SystemNBHA0092S0101
SHA247F
*1: HA-44
*2: HA-129
*3: HA-132
*4: HA-135
*5: HA-141*6: STEP-BY-STEP PROCEDURE
(HA-45), see No. 13.
*7: HA-90
*8: HA-94
*9: HA-66*10: HA-45
*11: HA-66
*12: HA-65
*13: HA-139
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
SC
EL
IDX
TROUBLE DIAGNOSES
Intake Door Motor
HA-87

SYSTEM DESCRIPTION=NBHA0056Component PartsNBHA0056S01Intake door control system components are:
1) Auto amp.
2) Intake door motor
3) A/C LAN system (PBR built-in mode motor and air mix door motor)
4) In-vehicle sensor
5) Ambient sensor
6) Sunload sensor
7) Intake sensor
System OperationNBHA0056S02The intake door control determines intake door position based on the ambient temperature, the intake air
temperature and the in-vehicle temperature. When the ECON, DEFROST, or OFF switches are pushed, the
auto amplifier sets the intake door at the ªFreshº position.
RHA874H
Intake Door Control SpecificationNBHA0056S03
RHA136G
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
SC
EL
IDX
TROUBLE DIAGNOSES
Intake Door Motor (Cont'd)
HA-89

2 CHECK FOR AUTO AMP. OUTPUT
Set up Self-diagnosis STEP 4.
Measure voltage across auto amp. harness terminals and body ground.
RHA821H
MTBL0466
OK or NG
OK©INSPECTION END
NG©GO TO 3.
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
SC
EL
IDX
TROUBLE DIAGNOSES
Intake Door Motor (Cont'd)
HA-91