MAZDA 626 1987 Workshop Manual

MAZDA 626 1987 Workshop Manual 626 1987 MAZDA MAZDA https://www.carmanualsonline.info/img/28/57059/w960_57059-0.png MAZDA 626 1987 Workshop Manual
Trending: automatic transmission fluid, door lock, battery capacity, heater, lights, climate control, fuel cap release

Page 1231 of 1865

MAZDA 626 1987  Workshop Manual 
ASSEMBLY 7C 
17. Install a new O-ring on the kick-down solenoid. 
18. Install the kick-down solenoid. 
76G07C-315 
19. Apply sealant to the threads and seat face of the 
switch; and install the inhib

Page 1232 of 1865

MAZDA 626 1987  Workshop Manual 
7C ASSEMBLY 
76G07C-319 

—
 "A" dimension 
iP^X 
VJjal ( 
f b 
v. r 
24. Fill the torque converter with ATF if it has been 
drained and washed. 
ATF type: Dexron II or M III 
25. Install the torq

Page 1233 of 1865

MAZDA 626 1987  Workshop Manual 
INSTALLATION 7C 
INSTALLATION 
TORQUE SPECIFICATIONS 
16—23 N m (1.6—2.3 m-kg, 12—17 ft-lb) 
36—54 N m (3.7—5.5 m-kg, 27—40 ft-lb) Jf^^ 5—7 N-m (50—70 cm-kg, 43—61 in-lb) 
^ 9—13

Page 1234 of 1865

MAZDA 626 1987  Workshop Manual 
7C INSTALLATION 
86U07B-441 
86U07B-442 
76G07C-322 
1. Attach rope at 2 places on the transaxle. Place a 
flat board on a jack and set the transaxle on it. 
Caution 
The transaxle is not well balanc

Page 1235 of 1865

MAZDA 626 1987  Workshop Manual 
INSTALLATION 7C 
B 
i^sN | 
-- f  
®4 4-1; 
6. Install the crossmember and the left side lower arm 
as an assembly. 
Tightening torque: 

(A)
 36—54 N m 
(3.7—5.5 m-kg, 27—40 ft-lb) 
(|) 75—

Page 1236 of 1865

MAZDA 626 1987  Workshop Manual 
7C INSTALLATION 
(3) Install and tighten the reamer bolts, then install 
and tighten the standard bolts. 
Tightening torque: 
Reamer bolts 7—10 N-m 
(70—100 cm-kg, 61—87 in-lb) 
Standard bolts

Page 1237 of 1865

MAZDA 626 1987  Workshop Manual 
INSTALLATION 7C 
76G07C-332 
19. Install the oil cooler outlet and inlet hoses. 
Note 
Align the mating mark as shown. 
20. Install the splash shields. 
Tightening torque: 
8—11 N-m (80—110 cm-kg

Page 1238 of 1865

MAZDA 626 1987  Workshop Manual 
7C INSTALLATION 
31. 
Connect the distributor lead. 
Connect the main fuse block. 
Tightening torque: 
8—11 N-m (80—110 cm-kg, 69—95 in-lb) 
Install the fresh air duct. 
Install the battery car

Page 1239 of 1865

MAZDA 626 1987  Workshop Manual 
HYDRAULIC CIRCUIT 7C 
HYDRAULIC CIRCUIT 
OUTLINE 
The flow of the individual hydraulic circuits are identified as listed below. 
(Numbers indicate individual circuits) 
Line pressure source 7 
Contro

Page 1240 of 1865

MAZDA 626 1987  Workshop Manual 
7C HYDRAULIC CIRCUIT 
P RANGE 
Apply side 
 
Release side 
Kick-down solenoid 
EZ3 Line pressure 
CZ1 Governor pressure 
cm Torque converter 
CU Throttle pressure Secondary x Primary governor valve g
Trending: charging, seat memory, engine oil capacity, spare wheel, fuel consumption, bulb, recommended oil