MITSUBISHI SPYDER 1990 Service Repair Manual

39.
40.
41.
44:
45.
46.
47.
50.
51.
52. 53.
Pulse generatorSpring washerControl lever
ClampPark/neutral position switch
Oil temperature sensor
End clutch cover
O-ring
BearingEnd clutch
Thrust washer
End clutch hub
Thrust bearing
End clutch shaftBearing retainer
Snap ring Lock plate
54. Idler gear shaft55. Bearing inner race’
56. Idler gear
57. Bearing inner race
58. Spacer
59. Snap ring .60. servo switch
61. servo piston
62. Spring
63. Anchor rod64. flange
65. Transfer shaft
66. Outer race
67. Gasket . .
,
68. O-ring
6 9 . V a l v e b o d y
TSB Revision

6AUTOMATIC TRANSAXLE
OVERHAUL Transaxle
70. Clamp
71.
Gasket
72. Oil pan
73.
Gasket
74.Drain plug
75.O-ring
76.Set screw77.O-ring78.Detent plate
79. Sprag rod support
80. Parking sprag rod
2170046
81.Control shaft
82. D-ring
83. Transfer shaft cover
84.Lock nut
85. Driven gear
86.Outer race
87.Spacer
-88.Outer race89.Transaxle case
(1) Prior to disassembling the transaxle, openings
and thoroughly clean the exterior of the, assembly, prefer-
ably by steam.
(2) Place the transmission on the ‘workbench with t he oil
pan down.
(3) Remove the torque converter.
.
(4)Measuring input shaft end play will
usually indicate when a thrust is required
(except when major parts are replaced). Thrust wash ers
are located between the shaft support and rear
clutch retainer, and between the reaction shaft sup port
and front clutch ‘retainer.
Mount a dial indicator to the converter housing usi ng
the special tool, with its plunger seated against t he end
of the input shaft.
Move the input shaft in and out with pliers to obta in the
end play reading. Be careful not to scratch the inp ut shaft.
Record the indicator reading for reference when rea ssem-
bling the transaxle.
(5) Remove pulse generators “A” and “B”.
(6) Remove the manual control lever, and then remov e
park/neutral position switch. ,
.
TSB Revision

A U T O M A T I C T R A N S A X L EOVERHAUL Transaxle
the snap ring and remove
switch.
(8) Remove the oil pan and oil gasket.
(9) Remove the oil filter.
the oil temperature sensor bracket. mounting
bolts’and remove the oil temperature sensor from brack-
et. Using a screwdriver, push out the rubber plug,
from inside the case, and remove the oil temperatur e
sensor from the case..
(11) With their catches pressed down, force the har
ness grom-
met and connector into the transaxle case:,
TSB Revision

8A U T O M A T I C T R A N S A X L E ’
OVERHAUL Transaxle
the valve body mounting bolts indicated by
aiid the valve. body from the transaxle
the end clutch
.
the end clutch
.
thrust washer from the end.
.
the end clutch hub and the thrust
TSB Revision

end , ,., ,
.
14
the housing and
the six
arrows. ,
the special the bolt ,
the oil’
remove the gasket.
,
, .
the the
case.
. . . . .
.
.

AUTOMATIC
OVERHAUL T r a n s a x l e
fiber thrust washer
.
. .
. .
input shaft to, remove the
and clutch assemblies
. .,
,,
. , ,
,
,
(25) Removethrust
the clutch hub. . . .
.
,
race and t h r u s t ,
.
. .
, ,
,--

A U T O M A T I C
OVERHAUL Transaxle , .
the d r u m .
(29) Remove
the special tools;’ push in the and
remove the snap ring.
,
,
,
.
the special tools remove the
servo piston, sleeve and
the anchor rod.
TSB Revision

AUTOMATIC TRANSAXLE
OVERHAUL Transaxle
Reverse gear
the snap ring.
the special tool on the center support and remove
the center support from the case.
reverse sun gear, thrust bearing thrust race
and forward sun gear together.”
the gear set and thrust bearing
the wave spring, return spring, reaction plate,
brake discs, and brake plates.
TSB Revision

AUTOMATIC TRANSAXLE
OVERHAUL ,
has been applied to the threads of
on the bearing retainer. Tap the heads so
can be easily loosened.
,
an impact driver, loosen the and remove
the bearing retained
.
,
,
the idler shaft lock plate.
. the transfer idler shaft with the
. .
. .
transfer idler
gear and the two bearing inner races inside the;
case..
TSB Revision

TRANSAXLE
AUL Transaxle
the spacer.
the snap ring from the flange bearing.
the output flange from the
t h e t r a n s f e r s h a f t c o v e r .
the locking tab the transfer lock nut,
where it is bent.
TSB RevisionI