NISSAN TIIDA 2007 Service Repair Manual

TCM
TM-425
< ECU DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
*1: These terminals are connected to the data link connector.
*2: These terminals are connected to the ECM.34 LG PNP switch “D” position
and When setting selector lever to “D” posi-
tion.Battery voltage
When setting selector lever to other po-
sitions.0V
35 SB PNP switch “R” positionWhen setting selector lever to “R” posi-
tion.Battery voltage
When setting selector lever to other po-
sitions.0V
36 RPNP switch “N” or “P”
positionWhen setting selector lever to “N” or “P”
position.Battery voltage
When setting selector lever to other po-
sitions.0V
38 GTurbine revolution sen-
sor (power train revolu-
tion sensor)When driving at 20 km/h (12 MPH) 360 Hz
39
*2L Engine speed signal
and Refer to XX-XX, "*****".
40 O Vehicle speed sensorWhen driving vehicle at 2 to 3 km/h (1 to
2 MPH) for 1 m (3 ft) or more.Voltage varies
between less
than 0V and
more than 4.5V
42 B Sensor ground Always 0V
47 BRA/T fluid temperature
sensor
and When A/T fluid temperature is 20°C
(68°F).1.5V
When A/T fluid temperature is 80°C
(176°F).0.5V
48 B Ground Always 0V Te r m i n a lWire
colorItem ConditionJudgement stan-
dard (Approx.)

TM-426
< ECU DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
TCM
Wiring Diagram - A/T CONTROL SYSTEM -
INFOID:0000000001714340
Fail-SafeINFOID:0000000001714341
The TCM has an electronic Fail-safe mode. This allows the vehicle to be driven even if a major electrical input/
output device circuit is damaged.
Under Fail-Safe, the vehicle always runs in third gear, even with a shift lever position of “1”, “2” or “D”. The cus-
tomer may complain of sluggish or poor acceleration.
Always follow TM-10, "
Work Flow".
ALDWA0057GB

TCM
TM-427
< ECU DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
The SELF-DIAGNOSIS results will be as follows:
 The first SELF-DIAGNOSIS will indicate damage to the vehicle speed sensor or the revolution sensor.
 During the next SELF-DIAGNOSIS, performed after checking the sensor, no damages will be indicated.
FAIL-SAFE FUNCTION
The following fail-safe functions allow vehicles to be driven even when sensor, switch or solenoid malfunction
occurs.
Vehicle Speed Sensor·A/T (Revolution Sensor)
Vehicle speed sensor·MTR signal is input from combination meter.
Accelerator Pedal Position Sensor Signal and Throttle Position Sensor Signal
TCM controls the throttle opening angle to a predetermined fixed position to enable driving if a malfunctioning
signal is input to TCM.
PNP Switch
When the multiple PNP switch signals are input to TCM, the priority of selector lever position becomes “D”,
“N”, “R”, “2” and “1” in order by internal TCM determination.
The use of 4th gear is inhibited until normal operation resumes. Because the hydraulic circuit of the control
valve is switched by manual valve according to the selector lever position, however, actual operating condition
of vehicle becomes as follows.
Shift Solenoid Valve A and B
If non-standard solenoid signal is sent to TCM, use of certain gears is limited. Refer to chart shown below.
●: Solenoid ON
×: Solenoid OFF
–: Non-standard condition
Line Pressure Solenoid Valve
If non-standard solenoid signal is sent to TCM, line pressure solenoid valve is turned OFF to achieve maxi-
mum oil pressure.
Torque Converter Clutch Solenoid Valve
Actual lever position PNP switch input signal Running status
“P” “P” position and other position signals P
“R” “R” position and other position signals R
“N” “N” position and other position signals N
“D” “D” position and other position signals D
1⇔D2⇔D3⇔D4
“2”“2” position and other position signals (Except “1” position) 21⇔22⇔23
“2” position and “1” position signals 21⇔22
“1”“1” position and other position signals (Except “2” position) 11⇔12⇔13
“1” position and “2” position signals 11⇔12
Shift positionNormalMalfunction in solenoid
valve AMalfunction in solenoid
valve BMalfunction in solenoid
valves A and B
A BGearABGearABGearABGear
“D” position●●1st –●→×
3rd ●→×–
3rd ––
3rd ×●2nd –●→× ×–––
××3rd – x×–––
●×4th – x●→×–––
“2” position●●1st –●→×●→×–––
×●2nd –●→× ×–––
××3rd – x×–––
“1” position●●1st –●→×●→×–––
×●2nd –●→× ×–––
××3rd – x×–––

TM-428
< ECU DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
TCM
If non-standard solenoid signal is sent to TCM, torque converter clutch solenoid valve is turned OFF to release
lock-up.
Overrun Clutch Solenoid Valve
If non-standard solenoid signal is sent to TCM, overrun clutch solenoid valve is turned OFF to engage overrun
clutch. This will result in more effective engine brake during deceleration.
Alphabetical IndexINFOID:0000000001714344
NOTE:
If DTC “CAN COMM CIRCUIT” is displayed with other DTCs, first perform the trouble diagnosis for
DTC “CAN COMM CIRCUIT”. Refer to XX-XX, "*****"
.
X: Applicable, —: Not applicable
Items (CONSULT-II screen terms)TCM self-diagnosis
Reference
page OD OFF indi-
cator lamp“A/T” with
CONSULT-II
A/T 1ST GR FNCTN — XXX-XX, "*****"
A/T 2ND GR FNCTN — XXX-XX, "*****"
A/T 3RD GR FNCTN — XXX-XX, "*****"
A/T 4TH GR FNCTN — XXX-XX, "*****"
A/T TCC S/V FNCTN — XXX-XX, "*****"
BATT/FLUID TEMP SEN X XXX-XX, "*****"
CAN COMM CIRCUIT X XXX-XX, "*****"
CONTROL UNIT (RAM) — XXX-XX, "*****"
CONTROL UNIT (ROM) — XXX-XX, "*****"
ENGINE SPEED SIG X XXX-XX, "*****"
LINE PRESSURE S/V X XXX-XX, "*****"
OVERRUN CLUTCH S/V X XXX-XX, "*****"
SHIFT SOLENOID/V A X XXX-XX, "*****"
SHIFT SOLENOID/V B X XXX-XX, "*****"
T/C CLUTCH SOL/V X XXX-XX, "*****"
THROTTLE POSI SEN X XXX-XX, "*****"
TURBINE SENSOR X XXX-XX, "*****"
VHCL SPEED SEN-A/T X XXX-XX, "*****"
VHCL SPEED SEN-MTR X XXX-XX, "*****"

SYSTEM SYMPTOM
TM-429
< SYMPTOM DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
SYMPTOM DIAGNOSIS
SYSTEM SYMPTOM
Symptom ChartINFOID:0000000001714345
Numbers are arranged in order of inspection.
Perform inspections starting with number one and work up.
Items Symptom Condition Diagnostic item Reference page
No Lock-up Engage-
ment/TCC InoperativeTorque converter is
not locked up.ON vehicle1. Accelerator pedal position sensorEC-583
2. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRXX-XX, "*****"
and XX-XX,
"*****"
3. Engine speed signalXX-XX, "*****"
4. A/T fluid temperature sensorXX-XX, "*****"
5. Line pressure testXX-XX, "*****"
6. Torque converter clutch solenoid valveXX-XX, "*****"
7. Control valve assemblyXX-XX, "*****"
OFF vehicle 8. Torque converterXX-XX, "*****"
Torque converter
clutch piston slip.ON vehicle1. A/T fluid levelXX-XX, "*****"
2. Accelerator pedal position sensorEC-583
3. Line pressure testTM-178
4. Torque converter clutch solenoid valveXX-XX, "*****"
5. Line pressure solenoid valveXX-XX, "*****"
6. Control valve assemblyXX-XX, "*****"
OFF vehicle 7. Torque converterXX-XX, "*****"
Lock-up point is ex-
tremely high or low.ON vehicle1. Accelerator pedal position sensorEC-5832. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRXX-XX, "*****"
and XX-XX,
"*****"
3. Torque converter clutch solenoid valveXX-XX, "*****"
4. Control valve assemblyXX-XX, "*****"

TM-430
< SYMPTOM DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
SYSTEM SYMPTOM
Shift ShockSharp shock in shift-
ing from “N” to “D” po-
sition.ON vehicle1. Engine idling speedXX-XX, "*****"

(Type 1), XX-XX,
"*****" (Type 2)
2. Accelerator pedal position sensorEC-297
(Type 1),
EC-583
(Type 2)
3. Line pressure testTM-178
4. A/T fluid temperature sensorTM-48
(Type 1),
XX-XX, "*****"

(Type 2)
5. Engine speed signalTM-56
(Type 1),
XX-XX, "*****"

(Type 2)
6. Line pressure solenoid valveTM-81
(Type 1),
XX-XX, "*****"

(Type 2)
7. Control valve assemblyXX-XX, "*****"
8. Accumulator N-DXX-XX, "*****"
OFF vehicle 9. Forward clutchXX-XX, "*****"
Too sharp a shock in
changing from D
1 to
D
2.ON vehicle1. Accelerator pedal position sensorEC-297
(Type 1),
EC-583
(Type 2)
2. Line pressure testTM-178
3. Accumulator servo releaseXX-XX, "*****"
4. Control valve assemblyXX-XX, "*****"
5. A/T fluid temperature sensorTM-48
(Type 1),
XX-XX, "*****"

(Type 2)
OFF vehicle 6. Brake bandXX-XX, "*****"
Too sharp a shock in
changing from D
2 to
D
3.ON vehicle1. Accelerator pedal position sensorEC-297
(Type 1),
EC-583
(Type 2)
2. Line pressure testTM-178
3. Control valve assemblyXX-XX, "*****"
OFF vehicle4. High clutchXX-XX, "*****"5. Brake bandXX-XX, "*****"
Too sharp a shock in
changing from D
3 to
D
4.ON vehicle1. Accelerator pedal position sensorEC-297
(Type 1),
EC-583
(Type 2)
2. Line pressure testTM-178
3. Control valve assemblyXX-XX, "*****"
OFF vehicle4. Brake bandXX-XX, "*****"5. Overrun clutchXX-XX, "*****"
6. Forward one-way clutchXX-XX, "*****"
Gear change shock
during deceleration by
releasing accelerator
pedal.ON vehicle1. Accelerator pedal position sensorEC-297
(Type 1),
EC-583
(Type 2)
2. Line pressure testTM-178
3. Overrun clutch solenoid valveTM-93
(Type 1),
XX-XX, "*****"

(Type 2)
4. Control valve assemblyXX-XX, "*****"
Large shock in chang-
ing from 1
2 to 11 in “1”
position.ON vehicle 1. Control valve assemblyXX-XX, "*****"OFF vehicle 2. Low & reverse brakeXX-XX, "*****"
Items Symptom Condition Diagnostic item Reference page

SYSTEM SYMPTOM
TM-431
< SYMPTOM DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
Improper Shift TimingToo high a gear
change point from D
1
to D
2, from D2 to D3,
from D
3 to D4.ON vehicle1. Accelerator pedal position sensorEC-583
2. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRXX-XX, "*****"
and XX-XX,
"*****"
3. Shift solenoid valve AXX-XX, "*****"
4. Shift solenoid valve BXX-XX, "*****"
Gear change directly
from D
1 to D3 occurs.ON vehicle1. A/T fluid levelXX-XX, "*****"2. Accumulator servo releaseXX-XX, "*****"
OFF vehicle 3. Brake bandXX-XX, "*****"
Too high a change
point from D
4 to D3,
from D
3 to D 2, from
D
2 to D1.ON vehicle1. Accelerator pedal position sensorEC-583
2. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRXX-XX, "*****"
and XX-XX,
"*****"
Kickdown does not
operate when de-
pressing accelerator
pedal in D
4 within
kickdown vehicle
speed.ON vehicle1. Accelerator pedal position sensorEC-583
2. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRXX-XX, "*****"
and XX-XX,
"*****"
3. Shift solenoid valve AXX-XX, "*****"
4. Shift solenoid valve BXX-XX, "*****"
Kickdown operates or
engine overruns when
depressing accelera-
tor pedal in D
4 beyond
kickdown vehicle
speed limit.ON vehicle1. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRXX-XX, "*****"

and XX-XX,
"*****"
2. Accelerator pedal position sensorEC-583
3. Shift solenoid valve AXX-XX, "*****"
4. Shift solenoid valve BXX-XX, "*****"
Gear change from 22
to 2
3 in “2” position.ON vehicle1. PNP switch adjustmentXX-XX, "*****"2. Control cable adjustmentXX-XX, "*****"
Gear change from 11
to 1
2 in “1” position.ON vehicle1. PNP switch adjustmentXX-XX, "*****"2. Control cable adjustmentXX-XX, "*****"
Items Symptom Condition Diagnostic item Reference page

TM-432
< SYMPTOM DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
SYSTEM SYMPTOM
No Down ShiftFailure to change
gear from D
4 to D3.ON vehicle1. A/T fluid levelXX-XX, "*****"
2. Accelerator pedal position sensorEC-583
3. Overrun clutch solenoid valveXX-XX, "*****"
4. Shift solenoid valve A XX-XX, "*****"
5. Line pressure solenoid valveXX-XX, "*****"
6. Control valve assemblyXX-XX, "*****"
OFF vehicle7. Brake bandXX-XX, "*****"8. Overrun clutchXX-XX, "*****"
Failure to change
gear from D
3 to D2 or
from D
4 to D2.ON vehicle1. A/T fluid levelXX-XX, "*****"
2. Accelerator pedal position sensorEC-583
3. Shift solenoid valve AXX-XX, "*****"
4. Shift solenoid valve BXX-XX, "*****"
5. Control valve assemblyXX-XX, "*****"
OFF vehicle6. High clutchXX-XX, "*****"7. Brake bandXX-XX, "*****"
Failure to change
gear from D
2 to D1 or
from D
3 to D1.ON vehicle1. A/T fluid levelXX-XX, "*****"
2. Accelerator pedal position sensorEC-583
3. Shift solenoid valve AXX-XX, "*****"
4. Shift solenoid valve BXX-XX, "*****"
5. Control valve assemblyXX-XX, "*****"
OFF vehicle6. Low one-way clutchXX-XX, "*****"7. High clutchXX-XX, "*****"
8. Brake bandXX-XX, "*****"
Failure to change
from D
3 to 22 when
shifting selector lever
into “2” position.
XX-XX, "*****"ON vehicle1. Accelerator pedal position sensorEC-5832. Shift solenoid valve BXX-XX, "*****"
3. Control valve assembly XX-XX, "*****"
4. Control cable adjustmentXX-XX, "*****"
OFF vehicle 5. Brake bandXX-XX, "*****"
No Down ShiftDoes not change from
12 to 11 in 1st position.ON vehicle1. PNP switch adjustmentXX-XX, "*****"
2. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRXX-XX, "*****"
and XX-XX,
"*****"
3. Shift solenoid valve AXX-XX, "*****"
4. Control valve assemblyXX-XX, "*****"
5. Overrun clutch solenoid valveXX-XX, "*****"
OFF vehicle6. Overrun clutchXX-XX, "*****"7. Low & reverse brakeXX-XX, "*****"
Items Symptom Condition Diagnostic item Reference page

SYSTEM SYMPTOM
TM-433
< SYMPTOM DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
No Up ShiftFailure to change
gear from D
1 to D2.ON vehicle1. Control cable adjustmentXX-XX, "*****"
2. Shift solenoid valve AXX-XX, "*****"
3. Control valve assemblyXX-XX, "*****"
4. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRXX-XX, "*****"
and XX-XX,
"*****"
5. Accelerator pedal position sensorEC-583
OFF vehicle 6. Brake bandXX-XX, "*****"
Failure to change
gear from D
2 to D3.ON vehicle1. Control cable adjustmentXX-XX, "*****"
2. Shift solenoid valve BXX-XX, "*****"
3. Control valve assemblyXX-XX, "*****"
4. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRXX-XX, "*****"
and XX-XX,
"*****"
5. Accelerator pedal position sensorEC-583
OFF vehicle6. High clutchXX-XX, "*****"7. Brake bandXX-XX, "*****"
Failure to change
gear from D
3 to D4.ON vehicle 1. PNP switch adjustmentXX-XX, "*****"
2. Overdrive control switchXX-XX, "*****"
3. Control cable adjustmentXX-XX, "*****"
4. Shift solenoid valve AXX-XX, "*****"
5. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRXX-XX, "*****"
and XX-XX,
"*****"
6. A/T fluid temperature sensorXX-XX, "*****"
OFF vehicle 7. Brake band XX-XX, "*****"
No Up ShiftA/T does not shift to
D4 when driving with
OD ON. (OD OFF in-
dicator lamp is off.)ON vehicle1. Accelerator pedal position sensorEC-583
2. PNP switch adjustmentXX-XX, "*****"
3. Overdrive control switchXX-XX, "*****"
4. Vehicle speed sensor·A/T (Revolution sensor)
and vehicle speed sensor·MTRXX-XX, "*****"
and XX-XX,
"*****"
5. Shift solenoid valve AXX-XX, "*****"
6. Overrun clutch solenoid valveXX-XX, "*****"
7. Control valve assemblyXX-XX, "*****"
8. A/T fluid temperature sensorXX-XX, "*****"
9. Line pressure solenoid valveXX-XX, "*****"
OFF vehicle10. Brake bandXX-XX, "*****"11. Overrun clutchXX-XX, "*****"
Items Symptom Condition Diagnostic item Reference page

TM-434
< SYMPTOM DIAGNOSIS >[TYPE 2 (4AT: RE4F03B)]
SYSTEM SYMPTOM
Slips/Will Not EngageVehicle will not run in
“R” position (but runs
in “D”, “2” and “1” po-
sitions). Clutch slips.
Very poor accelera-
tion.ON vehicle1. Control cable adjustmentXX-XX, "*****"
2. Stall testXX-XX, "*****"
3. Line pressure testTM-178
4. Line pressure solenoid valveXX-XX, "*****"
5. Control valve assemblyXX-XX, "*****"
OFF vehicle6. Reverse clutchXX-XX, "*****"
7. High clutchXX-XX, "*****"
8. Forward clutchXX-XX, "*****"
9. Overrun clutchXX-XX, "*****"
10. Low & reverse brakeXX-XX, "*****"
Vehicle will not run in
“D” and “2” positions
(but runs in “1” and
“R” positions).ON vehicle 1. Control cable adjustmentXX-XX, "*****"
OFF vehicle 2. Low one-way clutchXX-XX, "*****"
Items Symptom Condition Diagnostic item Reference page