NISSAN X-TRAIL 2003 Electronic Repair Manual

TURN SIGNAL AND HAZARD WARNING LAMPS
LT-23
C
D
E
F
G
H
I
J
L
MA
B
LT
Removal and Installation for Side Turn Signal LampEKS003BI
1. Push the side turn signal lamp toward A direction in the figure,
and pull up B direction in the figure.
2. Disconnect the side turn signal lamp connector.
Removal and Installation for Rear Turn Signal LampEKS003BJ
Refer toLT- 4 2 , "REAR COMBINATION LAMP"
PKIA0469E

LT-24
LIGHTING AND TURN SIGNAL SWITCH
LIGHTING AND TURN SIGNAL SWITCH
PFP:25540
Removal and InstallationEKS0034F
1. Remove the steering column cover. Refer toPS-9, "STEERING
COLUMN"in “POWER STEERING SYSTEM (PS)” section.
2. Remove lighting and turn signal switch mounting screw and
remove the lighting and turn signal switch from the spiral cable.
3. Disconnect the lighting and turn signal switch connector.
Switch Circuit InspectionEKS0034G
Using circuit tester, check continuity between the lighting and turn signal switch connector terminals in each
operation status of the switch.
Lighting switch is refer toLT- 5 , "
Wiring Diagram—H/LAMP—"
Turn signal lamp switch is refer toLT-19, "Wiring Diagram—TURN—"
Front fog lamp switch is refer toLT-3 4, "Wiring Diagram—F/FOG—"
Rear fog lamp switch is refer toLT- 3 7 , "Wiring Diagram -R/FOG-/Without Front Fog Lamp",LT-38, "Wiring Dia-
gram -R/FOG-/With Front Fog Lamp"
PKIA0470E

HAZARD SWITCH
LT-25
C
D
E
F
G
H
I
J
L
MA
B
LT
HAZARD SWITCHPFP:25290
Removal and InstallationEKS003BZ
REMOVAL
1. Remove Instrument lower center panel. Refer toIP-3, "INSTRU-
MENT PANEL ASSEMBLY".in “INSTRUMENT PANEL (IP)”
section.
2. Using a flat-bladed screwdriver or other suitable tool, press pawl
to remove hazard switch from Instrument lower center panel.
INSTALLATION
Installation is in the reverse order of removal.
SKIA0061E

LT-26
STOP LAMP
STOP LAMP
PFP:26550
Wiring Diagram — STOP/L —EKS0034I
TKWA0067E

STOP LAMP
LT-27
C
D
E
F
G
H
I
J
L
MA
B
LT
Bulb ReplacementEKS0034K
STOP LAMP
Refer toLT- 4 2 , "REAR COMBINATION LAMP"
HIGH-MOUNTED STOP LAMP
1. Remove the high-mounted stop lamp cover. Refer toLT- 2 7 ,
"HIGH-MOUNTED STOP LAMP"in “Removal and Installation”.
2. Turn the high-mounted stop lamp bulb socket counterclockwise
and unlock it.
3. Remove the bulb.
Removal and InstallationEKS0034L
STOP LAMP
Refer toLT- 4 2 , "REAR COMBINATION LAMP"
HIGH-MOUNTED STOP LAMP
1. Open the backdoor. Then, pull the edge of the cover (A in the
figure below) to each side in turn downward until the pawls
inside the cover are released.
2. Pull down the cover toward under the vehicle.
3. Remove the high-mounted stop lamp mounting bolts.
4. Disconnect the high-mounted stop lamp connector and remove
from the vehicle.High-mounted Stop Lamp : 12V 5W
PKIA0496E
PKIA0497E
PKIA0498E

LT-28
BACK-UP LAMP
BACK-UP LAMP
PFP:26550
Wiring Diagram — BACK/L —EKS003C3
TKWA0068E

BACK-UP LAMP
LT-29
C
D
E
F
G
H
I
J
L
MA
B
LT
Bulb ReplacementEKS003C4
Refer toLT- 4 2 , "REAR COMBINATION LAMP".
Removal and InstallationEKS003C5
Refer toLT-42, "REAR COMBINATION LAMP".

LT-30
PARKING, LICENSE PLATE AND TAIL LAMPS
PARKING, LICENSE PLATE AND TAIL LAMPS
PFP:26550
Wiring Diagram — TAIL/L —EKS003C0
TKWA0065E

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-31
C
D
E
F
G
H
I
J
L
MA
B
LT
TKWA0066E

LT-32
PARKING, LICENSE PLATE AND TAIL LAMPS
Bulb Replacement
EKS003C1
PARKING AND TAIL LAMPS
Refer toLT- 4 2 , "REAR COMBINATION LAMP".
LICENSE PLATE LAMP
1. Remove license plate lamp.
2. Turn bulb socket, then remove it.
Removal and InstallationEKS003C2
PARKING AND TAIL LAMPS
Refer toLT- 4 2 , "REAR COMBINATION LAMP"
LICENSE PLATE LAMP
Removal
1. Remove the license lamp finisher. Refer toEI-22, "LICENSE
LAMP FINISHER"in “EXTERIOR & INTERIOR (EI)” section.
2. Remove the harness from installation pawl for harness.
3. Remove license plate lamp mounting screws (2 each, RH and
LH).
4. Pull out license plate lamp from finisher.
Installation
lInstall license plate lamp in the reverse order of removal, observing the tightening torque shown below.
License plate lamp mounting screwsLicense plate lamp : 12 V 5 W
SKIA0055E
Tightening torque :1.0 - 1.8 N-m (0.10 - 0.19 kg-m,9-
16 in-lb)