RENAULT KANGOO 1997 KC / 1.G Foult Finding - Injection Workshop Manual
Manufacturer: RENAULT, Model Year: 1997, Model line: KANGOO, Model: RENAULT KANGOO 1997 KC / 1.GPages: 363
Page 301 of 363

v0406.0
IMMOBILISER
Fault finding- Interpretation of XR25 Bargraphs 82
When communication is established, deal with any fault bargraphs which may
be illuminated.
Carry out a conformity check.AFTER REPAIR
Bargraph 1 right hand side extinguished
XR25 KIT / DECODER UNIT COMMUNICATION
1
Check that lines K and L are not being disrupted by another computer.NOTES
Fiche n° 56
Check the condition of +before ignition feed fuse.
Change the fuse if necessary.
Ensure that the XR25 kit is not the cause of the fault by trying to communicate with another computer on
the vehicle (air conditioning computer, injection computer...).
Check that the ISO interface is in position S8, that the most recent version of the XR25 cassette and the
correct access code are being used(D 56).
Check battery voltage (U > 10.5 volts). Recharge the battery if necessary.
Check that the 18 track decoder unit connector is properly connected.
Check that the decoder unit is properly fed :
-earth on track A8 of the decoder unit connector.
-+ before ignition feed on tracks A9 and A1 of the decoder unit connector.
Ensure that the diagnostic socket is correctly fed.
Check and ensure the continuity and insulation of the wiring of tracks A3 and A4 of the decoder unit
connector.
If there is still no dialogue between the XR25 kit and the decoder unit, change the decoder unit.
82-4
Page 302 of 363

v0406.0
IMMOBILISER
Fault finding- Interpretation of XR25 Bargraphs 82
Erase the memorised fault by entering G0** on the XR25 keyboard.
Carry out a conformity check.
Check that the immobiliser system is operating.AFTER REPAIR
Bargraph 3 right hand side incorrect illumination
CODED DIESEL SOLENOID VALVE CONFIGURATION
3
NONENOTES
Fiche n° 56
Using the XR25 kit, correctly reconfigure the decoder unit.
On the XR25 keyboard, enter G22*1* for a petrol vehicle
or G22*2* for a diesel vehicle
NOTE: In the diesel version, incorrect configuration of the decoder unit does not prevent proper
operation of the immobiliser. Nevertheless, if there is a fault, the immobiliser warning light will
not illuminate.
82-5
Page 303 of 363

v0406.0
IMMOBILISER
Fault finding- Interpretation of XR25 Bargraphs 82
Carry out a conformity check.
Check operation of the immobiliser system.AFTER REPAIR
Bargraph 4 right hand side incorrect illumination
+ AFTER IGNITION PRESENT
4
Reminder: Under normal operation :
- BG 4 right hand side illuminated ignition switch in position+after ignition
- BG 4 RH side extinguished ignition switch in a position other than +after
ignition.NOTES
Fiche n° 56
Check condition of the +after ignition fuse.
Change the fuse if necessary.
Ignition on , check for voltage of + 12 volts on track A7 of the 18 track decoder unit connector.
Are there 12 volts ?
Change the decoder unit.YES
NORepair the electrical wiring between track A7 of the 18 track decoder unit
connector and the passenger compartment fuse board.
82-6
Page 304 of 363

Check the insulation in relation to earth of
the electrical wiring between :
B2 B3
B5 A1
Is there insulation from earth?
v0406.0
IMMOBILISER
Fault finding- Interpretation of XR25 Bargraphs 82
Erase the memorised fault by entering GO** on the XR25 keyboard.
Carry out a conformity check.
Check operation of the immobiliser system.AFTER REPAIR
Bargraph 5 left hand side illuminated
CENTRAL LOCKING SWITCH (CPE)
5
Check that the central locking switch is not permanently depressed as the result of
a mechanical fault .NOTES
Fiche n° 56
Decoder
unit
Central locking
switch
YES
Change the central locking switch.
NORepair the faulty electrical wiring.
82-7
Page 305 of 363

v0406.0
IMMOBILISER
Fault finding- Interpretation of XR25 Bargraphs 82
Erase the memorised fault by entering GO** on the XR25 keyboard.
Carry out a conformity check.
Check operation of the immobiliser system.AFTER REPAIR
Bargraph 6 left hand side illuminated
DIESEL SOLENOID VALVE CLEARANCE
6
Check that the computer configuration is correct :
- diesel : Bargraph 3 right hand side illuminated
- petrol : Bargraph 3 right hand side extinguishedNOTES
Fiche n° 56
Set the XR25 to pulse sensor mode (button "G", input on terminal "Vin").
Ignition on, check for pulses on track A6 of the 18 track decoder unit connector (test with the decoder
unit and the coded electronic unit of the solenoid valve connectors connected).
Ignition on, if there are no pulses, change the decoder unit.
Switch on the ignition for 30 consecutive seconds, then switch off the ignition and wait until the
immobiliser warning light flashes (immobiliser active).
Switch on the ignition again and check that bargraph 8 left hand side is permanently illuminated.
Is Bargraph 8 left hand side permanently illuminated ?
Replace the decoder unit.YES
NOReplace the solenoid valve coded electronic unit.
82-8
Page 306 of 363

v0406.0
IMMOBILISER
Fault finding- Interpretation of XR25 Bargraphs 82
Erase the memorised fault by entering GO** on the XR25 keyboard.
Carry out a conformity check.
Check operation of the immobiliser system.AFTER REPAIR
Bargraphs 6 left and 6 right hand side illuminated
ACCEPTANCE (CLEARANCE) OF THE SIGNAL BY THE DIESEL
SOLENOID VALVE AND CODED LINE
6
Before beginning the fault finding, switch on the ignition for longer than 30
consecutive seconds, then switch off the ignition.NOTES
Fiche n° 56
Ensure that the connector of the coded electronic unit of the solenoid valve is properly connected.
Set the XR25 to pulse sensor mode (button "G", input on terminal "Vin").
Ignition on, check for pulses on track A6 of the decoder unit connector (test with decoder unit and
solenoid valve coded electronic unit connectors connected).
Are there any pulses?
Replace the solenoid valve side electronic unit.YES
NOReplace the decoder unit.
For the diesel version, if bargraphs 6 right and 6 left are illuminated, check the impact switch.
Check the condition of the electrical wiring between track A6 of the decoder unit and track 8 of the
coded solenoid valve connector and check the 12 Volts supply and earth.
Repair if necessary.
82-9
Page 307 of 363

v0406.0
IMMOBILISER
Fault finding- Interpretation of XR25 Bargraphs 82
AFTER REPAIR
Bargraph 6 right hand side illuminated
CODED LINE
6
NONE.NOTES
Fiche n° 56
Check the continuity and insulation from earth and from 12 volts of the wiring between track A6 of the
18 track decoder unit connector and track ** of the injection computer .
Repair the wiring if necessary.
Set the XR25 to pulse sensor mode (button "G", input on terminal "Vin").
Ignition on, check for pulses on track A6 of the decoder unit connector (test with decoder unit and
solenoid valve coded electronic unit connectors connected).
Are there any pulses ?
Replace the injection computer.YES
NOReplace the decoder unit.
** track : 43 or 19 depending on engine
Erase the memorised fault by entering GO** on the XR25 keyboard.
Carry out a conformity check.
Check operation of the immobiliser system.
For petrol vehicles, if bargraph 6 right hand side is illuminated, check the impact switch.
82-10
Page 308 of 363

Check the continuity and insulation with earth and 12 volts of the wiring between :
18 track decoder unit connector (A2 4) antenna ring
Repair the wiring if necessary.
v0406.0
IMMOBILISER
Fault finding- Interpretation of XR25 Bargraphs 82
AFTER REPAIR
Bargraph 7 right hand side illuminated or flashing
ANTENNA RING/DECODER UNIT CONNECTION
XR25 aid: *27 = cc.1 short circuit+ 12 volts
co.0 open circuit
7
None.NOTES
Fiche n° 56
Ignition off, check for + 12 volts on track A2 of the decoder unit connector, wiring side (decoder
connector disconnected and antenna ring connector connected).
If 12 volts + before ignition feed are not measured, replace the +before ignition feed fuse
If the problem persists, replace the antenna ring.
Check that the antenna ring is properly fed with earth on track 2 and 12 Volts on track 3.
Disconnect the 4 track antenna ring connector.
Set the XR25 to pulse sensor mode (button "G", input on terminal "Vin").
When switching the ignition on again, check for a pulse on track A2 of the 18 track decoder unit
connector (test with decoder unit and antenna ring connectors connected).
When the ignition is switched on, is there a pulse?
Replace the antenna ring.YES
NOReplace the decoder unit.
Erase the memorised fault by entering GO** on the XR25 keyboard.
Carry out a conformity check.
Check operation of the immobiliser system.
82-11
Page 309 of 363

Check the insulation in relation to the earth of the wiring between :
B1 B2
PLIP
decoder unit B2 B3 central locking
B5 A1 button
Are they insulated from earth ?
v0406.0
IMMOBILISER
Fault finding- Interpretation of XR25 Bargraphs 82
AFTER REPAIR
Bargraph 11 left hand side remains extinguished
after pressing the PLIP
PLIP SIGNAL RECEIVED
11
If BG 17right is illuminated, do not apply the following fault finding as the
decoder unit is new. Carry out the Plip programming procedure.
Only consult the following fault finding if BG 11 left remains extinguished after
having tried to lock or unlock the vehicle doors with the PLIP .
NOTES
Fiche n° 56
Check if locking or unlocking the doors is possible by testing with the other key. If locking or unlocking of
the vehicle doors is possible, replace the battery in the first key.
On the infrared transmitter connector, check for + 12 V before ignition feed between tracks B2 and A3.
Is this voltage present ?
Set the XR25 to pulse sensor mode (button "G", input on terminal "Vin").
Check for pulses on track B2 of the infrared transmitter by pressing the PLIP (test
with the decoder unit and infrared transmitter connectors connected).
Are there any pulses when the PLIP is pressed?YES
YES Replace the decoder unit.
NO Replace the infrared transmitter.
NO
YES Repair the faulty wiring.
NO Change the decoder unit.
Carry out a conformity check.
Check operation of the immobiliser system.
82-12
Page 310 of 363

v0406.0
IMMOBILISER
Fault finding- Interpretation of XR25 Bargraphs 82
AFTER REPAIRCarry out a conformity check.
Check operation of the immobiliser system.
Bargraph 11 right hand side remains extinguished
after pressing the PLIP
PLIP SIGNAL CORRECT
11
Only consult the fault finding which follows if, when the PLIP is pressed BG 11 left
illuminates for 3 seconds and BG 11 right remains extinguished.
Check that the keys belong to the vehicle.NOTES
Fiche n° 56
There is a desynchronisation between the PLIP code and the decoder unit code if bargraph 11 right
hand side remains extinguished when the PLIP is pressed (but bargraph 11 left hand side illuminates for
approximately 3 seconds before extinguishing) and locking or unlocking of the vehicle doors with the
PLIP is not possible.
Apply the procedure for resynchronising the PLIPs .
82-13