RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit Manual PDF

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-71
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-71V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
DF001
PRESENT
UCH
1.DEF: Internal electronic fault
2.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
Lock/unlock the vehicle by pressing the button on the card.
If the fault appears, carry out this fault finding procedure.
Special notes:
If a fault concerning the steering column lock is present or stored, deal with it first.
Contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF001P/UCH_V48_DF001P/UCH_V4C_DF001P/
UCH_V4D_DF001P/UCH_V4F_DF001P /UCH_V50_DF001P
MR-372-J84-87B000$301.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-72
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-72V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF002
PRESENT
STEERING LOCK
1.DEF: Steering lock internal electronic fault
2.DEF: Steering column lock internal electronic fault
3.DEF: Mechanical fault on column
4.DEF: Steering column lock authentication fault
5.DEF: Steering column lock authentication fault
6.DEF: UCH internal electronic fault
7.DEF: Steering column lock internal electronic fault
8.DEF: Steering column lock internal electronic fault
NOTESPriorities when dealing with a number of faults:
Firstly, deal with fault DF029 Steering column lock circuit, if it is present.
Special notes:
Attempt to apply forced + after ignition feed to update the faults.
1.DEF
NOTESAttempt to apply forced + after ignition feed to update the
faults.
If the fault is still present, replace the steering column lock.
2.DEF
NOTESAttempt to apply forced + after ignition feed to update the
faults.
Make another attempt to lock/unlock the column.
If the fault is still present, replace the steering column lock.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF002P/UCH_V48_DF002P/UCH_V4C_DF002P/
UCH_V4D_DF002P/UCH_V4F_DF002P /UCH_V50_DF002P

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-73
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-73V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF002
CONTINUED 1
3.DEF
NOTESAttempt to apply forced + after ignition feed to update the
faults.
Release the column by turning the steering wheel, while pressing the start button.
If the fault is still present without mechanical fault (with the wheels set straight ahead), replace the steering column
lock.
4.DEF
NOTESAttempt to apply forced + after ignition feed to update the
faults.
The steering column lock does not belong to this vehicle (or the UCH and/or the cards do not belong to this vehicle).
Ensure the conformity of the vehicle.
If the fault is still present contact Techline.
5.DEF
NOTESAttempt to apply forced + after ignition feed to update the
faults.
The steering column lock does not belong to this vehicle (or the UCH and/or the cards do not belong to this vehicle).
Ensure the conformity of the vehicle.
If the fault is still present contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-74
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-74V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF002
CONTINUED 2
6.DEF
NOTESAttempt to apply forced + after ignition feed to update the
faults.
Make another attempt to lock/unlock the column.
If the fault is still present, replace the UCH.
7.DEF
NOTESAttempt to apply forced + after ignition feed to update the
faults.
If the vehicle is fitted with a Vdiag 0F ABS computer, or a Vdiag 0B or Vdiag 11 ABS/ESP computer: establish
dialogue with the ABS or ABS/ESP computer and verify that PR020 Vehicle speed on initialisation is correctly
configured. If the configuration is incorrect, use command VP032 Vehicle speed on initialisation to reconfigure
the ABS or the ABS/ESP.
Make five attempts to start and lock the column.
If the fault is still present, replace the steering column lock.
8.DEF
NOTESAttempt to apply forced + after ignition feed to update the
faults.
Deal with DF029 Steering column lock circuit first.
If the fault is still present, replace the steering column lock.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-75
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-75V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF003
PRESENT
OR
STOREDCLUTCH SWITCH CIRCUIT
CO.1: Short circuit or open circuit to + 12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault appears after a road test at speed > 60 mph (100 km/h).
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
CO.1
NOTESNone.
Check the condition and connection of the clutch switch connector (tabs bent, broken, oxidised, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the PE1 connector of the UCH (tabs bent, broken, oxidised, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity against + 12 V of the following connection:
●Connection code 26X between components 645 and 675.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for an earth on connection MAM of component 675.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connection, otherwise replace the wiring.
If the connection is OK and earth is present, replace the clutch switch.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF003 /UCH_V48_DF003/UCH_V4C_DF003/
UCH_V4D_DF003/UCH_V4F_DF003/UCH_V50_DF003

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-76
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-76V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF004
PRESENT
OR
STOREDBRAKE LIGHT SWITCH CIRCUIT
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault becomes present after 10 successive transitions of more than 1 second
between the released status and depressed status.
Note:
The fault could prevent cruise control/speed limiter operation.
Refer to the interpretation of status ET047 Brake pedal position.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF004 /UCH_V48_DF004/UCH_V4C_DF004/
UCH_V4D_DF004/UCH_V4F_DF004/UCH_V50_DF004

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-77
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-77V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF005
PRESENT
OR
STOREDCARD
1.DEF: Card battery low
1.DEF
NOTESConditions for applying the fault finding procedure to
stored faults:
Perform 5 start operations with each vehicle card.
Check the condition of the card battery and that it is inserted the right way round.
Replace the battery if necessary.
After each battery change, check that the fault does not recur after 5 starts.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF005 /UCH_V48_DF005/UCH_V4C_DF005/
UCH_V4D_DF005/UCH_V4F_DF005/UCH_V50_DF005

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-78
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-78V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF006
DF007
DF008
DF009
PRESENTFRONT LEFT-HAND WHEEL VALVE SENSOR
FRONT RIGHT-HAND WHEEL VALVE SENSOR
REAR RIGHT-HAND WHEEL VALVE SENSOR
REAR LEFT-HAND WHEEL VALVE SENSOR
2.DEF: Sensor internal electronic fault
3.DEF: Sensor internal electronic fault
4.DEF: Sensor internal electronic fault
5.DEF: Sensor internal electronic fault
6.DEF: Sensor internal electronic fault
7.DEF: Sensor internal electronic fault
8.DEF: Sensor internal electronic fault
1.DEF: No sensor signal.
NOTESSpecial notes:
Any operation involving the replacement of a valve, or the removal of a tyre requires
perfect knowledge of the precautions (see MR 364 (Mégane II) or MR 370 (Scénic II),
Mechanical, 35A, Wheels and tyres).
Before any operation, ensure that all the wheels have tyre pressure monitoring valves,
and that the spare wheel has not been fitted.
For faults DF006 to DF009, if the fault is present during the first few kilometres, reprogram the 4 valves.
In the event of a programming failure, replace the valve concerned (see MR 364 (Mégane II) or MR 370
(Scénic II), Mechanical, 35B, Tyre pressure monitor system)
Check that there are no wheels with rubber valves. If there are, replace them with wheels with a valve fitted with
a sensor and carry out a road test.
If the fault is still present, program the 4 valves.
If the fault is still present, replace the valve (see MR 364 (Mégane II) or MR 370 (Scénic II), Mechanical, 35B,
Tyre pressure monitor system).
The correspondence between fault numbers and the valve concerned is described below:
–DF006 Front left-hand wheel valve sensor,
–DF007 Front right-hand wheel valve sensor,
–DF008 Rear right-hand wheel valve sensor,
–DF009 Rear left-hand wheel valve sensor.
Once the sensor has been replaced, program the four valve codes according to procedure SC002 Programming
the four valve codes (see Configurations and programming).
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF006P/UCH_V44_DF007P/UCH_V44_DF008P/UCH_V44_DF009P/UCH_V48_DF006P/UCH_V48_DF007P/UCH_V48_DF008P/
UCH_V48_DF009P/UCH_V4C_DF006P/UCH_V4C_DF007P/UCH_V4C_DF008P/UCH_V4C_DF009P/UCH_V4D_DF006P/
UCH_V4D_DF007P/UCH_V4D_DF008P/UCH_V4D_DF009P/UCH_V4F_DF006P/UCH_V4F_DF007P/UCH_V4F_DF008P/
UCH_V4F_DF009P/UCH_V50_DF006P/UCH_V50_DF007P/UCH_V50_DF008P/UCH_V50_DF009P

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-79
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-79V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF010
PRESENT
OR
STORED
STEERING COLUMN SWITCH COMBINED CIRCUIT
1.DEF: The combined stalk is not connected or not correctly connected (stalk or UCH
side), not being supplied or has an internal electronic fault
2.DEF: Combined stalk lighting function connection to UCH in open circuit or internal
stalk fault
3.DEF: Combined stalk wiping function connection to UCH in open circuit or internal
stalk fault
4.DEF: Combined stalk direction indicator function connection to UCH in open circuit
or internal stalk fault
5.DEF: Combined stalk trip computer function connection to UCH in open circuit or
internal stalk fault
1.DEF
2.DEF
3.DEF
4.DEF
5.DEF
NOTESConditions for applying the fault finding procedure to a
stored fault:
If the fault becomes present after an action on the stalk, then
carry out this fault finding procedure.
Use Wiring Diagrams Technical Note for MEGANE II or
SCENIC II.
Check the condition and connection of the PE2 connector of the UCH (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the steering column control connector (tabs bent, broken, oxidised, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connections:
●Connection code 14 1B,
●Connection code 14 1K,
●Connection ode 14 1C,
●Connection code 141L,
●Connection code 14 1D,
●Connection code 14 1M,
●Connection code 14 1G,
●Connection code 14 1N,
●Connection code 14 1H,
●Connection code 14 1P.
Between components 645 and 1519.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If these connections are sound, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF010 /UCH_V48_DF010/UCH_V4C_DF010/
UCH_V4D_DF010/UCH_V4F_DF010/UCH_V50_DF010

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-80
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-80V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF011
PRESENT
OR
STOREDRAIN/LIGHT SENSOR CIRCUIT
1.DEF: Communication disrupted
2.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to a stored fault:
Run the automatic wiper system and automatic light illumination system, then cover the
sensor and/or place water on it.
If the fault appears, carry out this fault finding procedure.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
1.DEF
NOTESNone.
For vehicles which were manufactured after June 2005, check the condition and connection of the sensor supply
7.5A fuse located on the Protection and Switching Unit.
Replace it if necessary.
Check the condition and connection of the sensor connector (bent, oxidised, broken tabs etc.).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for an earth on connection MAM of component 1415.
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for + 12 V, BPT connection of component 1415 (timed + 12 V before ignition feed if the vehicle was
manufactured after June 2005). If the connection is faulty and if there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Ensure the continuity and the insulation of the following connection:
●Connection code BPT between components 645 and 1415.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for any intermediate connectors using the vehicle wiring diagram and repair if necessary.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF011/UCH_V48_DF011/UCH_V4C_DF011/
UCH_V4D_DF011/UCH_V4F_DF011 /UCH_V50_DF011