ECU JAGUAR X308 1998 2.G Owners Manual

9. Se
cure the shock absorber
to the upper mounting.
Posi
tion a wrench on the shock absorber shaft flats to
prevent rotation (wrench in socket on vehicles with
adaptive damping).
Tigh
ten the shock absorber upper lock nut to 30-40 Nm
(16-18 Nm on vehicles with adaptive damping).
10. Position the shock absorber and spring assembly to the
vehicle.

11
.
With assistance, manually re tract the shock absorber and
remove the temporary securing bolt.

12
.
Remove the special tools 204-179-1.
13. Align the shock absorber lower bush to the wishbone and
install the mounting bolt.
1. Install but do not tighten the nut.

18
.
Remove the special tools 204-179.

19
.
Fully seat and secure the u pper spring pan to the body.
Ensure the spri
ng pan is correctly seated in the body
location.
Inst
all the nuts securing the sp
ring pan to the body studs.

Tigh
ten to 17-23 Nm.

20
.
Tighten to 80-100 Nm.

21
.
Install the shims on the pivot pin sleeve in the positions
noted during removal.
22. Install the hub assembly to the wishbone assembly.
Position the hub and carri
er to the wishbone.
Inst

all the pivot pin ensuring that the ecce
ntric flange
correctly seats in the wishbone groove.

23. Inst
all the pivot pin nut.
Ali
g
n the marker on the pivo
t pin flange with the mark
made on wishbone.
Inst al
l the nut on to the pivot pin and, ensuring the pin
position is not dist urbed, tighten the nut to 88-118 Nm.
24. Release the tie strap securing the brake caliper to the
suspension mounting bracket.

25 . Install
the brake caliper on to the carrier.
1. Position the caliper asse mbly on to the carrier.
2. Install the guide pins and tighten to 25-30 Nm.
3. Install the dust caps.
4. Install the brake caliper spring clip.

26 . Conne
ct the wheel speed sensor electrical connector.
27. Using a new tie strap, secure the wheel speed sensor harness
to the brake hose clip.

St
abilizer Bar Vehicles With: Supercharger

64.35.08
Rubber Suspension Insulator Lube
Castrol NTR
Removal
1.
CA
UTION:
Replacement of nuts and bolts: Various thread-locking devices are used on nuts and bolts
throughout the vehicle. These devices restrict the number of times a nut or bolt can be used. See
section <<100-00>>

for information.
Raise vehicle on a four-post lift. Refer to section <<100-02>>.
2.
Remove nuts and bolts securing stabilizer bar to links.
3.

Remove stabilizer bar mounting-brackets.
 Remove bolts.

4
. Tighten nuts securing stabilizer bar to links.
5. Lower four-post lift.

St
abilizer Bar Bushing Vehicles With: Supercharger

64.35.18
Rubber Suspension Insulator Lube
Castrol NTR
Removal
1.
CA
UTION:
Replacement of nuts and bolts: Various thread-locking devices are used on nuts and bolts
throughout the vehicle. These devices restrict the number of times a nut or bolt can be used. See
section <<100-00>>

for information.
Raise vehicle on a four-post lift. Refer to section <<100-02>>.
2.
Remove nuts and bolts securing stabilizer bar to links.
3.

Remove stabilizer bar mounting-brackets.
 Remove bolts.

4
. Tighten nuts securing stabilizer bar to links.
5. Lower four-post lift.

Rear Suspension - Stabilizer Bar Mounting Frame
Remo
val and Installation
Remov
a
l
CAUTI
O
N: Replacement of
nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. See section 100-00 for information.
1. Ra
ise rear of vehicle and support
on stands. Refer to Section
100-02.

2. Support rear suspensio
n.
Posit
i
on a piece of wood under rear edge of suspension
unit.
Position an d
raise a jack
under wood to support
suspension unit.

3. Re
move monostrut lowe
r nuts and bolts.

4. Remove m
onostrut upper mounting
to body bracket securing
bolts.
5. Remove monostrut.
Lower rear edg
e
of suspension unit just sufficient for
access.
Exercising care to avoid dama ging fuel fil
ler neck drain
pipe, lift and withdraw monost rut from rear suspension.

9. P
osition special tool 204-195 on hub studs and install securing
nuts.

10
.
Slacken but do not remove hub to axle shaft securing nut.
11. Remove securing nuts and withdraw special tool (204-195)
from hub.
12. Remove rear brake disc. Refer to 70.10.13.
13. Remove parking brake shoe s. Refer to 70.40.05.

14
.
Remove wheel speed sensor.
Disc
onnect wheel speed sensor harness from sensor
R

emove wheel speed sensor se
curing bolt and withdraw
sensor from hub carrier.

15
.
Sever and discard wheel speed sensor harness tie strap and
position harness for access.
16. Remove hub nut and collar.
Re
move nut.

Remove l
ocating collar.

17 . Install a th
read protector on axle shaft.

18 . R
elease hub from axle shaft.
Pos
i
tion hub puller 204-011 on hub studs.
Inst
al
l securing nuts.
Progres
s
ively tighten
puller center bolt to release hub from
axle shaft splines.
19. Remove hub puller an d thread protector.
Re
move securing nuts and
release puller from hub.
Re
move thread protecto
r from axle shaft.

20 . Relea
se parking brake cable
from suspension mounting
bracket.
Remove cable reta ining clip.

Draw c
a
ble through suspension mounting bracket
aperture.
21. Remove parking brake cable to hub carrier grommet.