torque JAGUAR XFR 2010 1.G Workshop Manual
Page 972 of 3039
Installation
13.
NOTE: Do not disassemble further if the component is
removed for access only.
1. CAUTIONS:
Make sure that the mating faces are clean and free of
foreign material.
Make sure the anti-seize compound does not contact
the catalyst monitor sensor tip.
If accidentally dropped or knocked install a new
sensor.
Make sure the catalyst monitor sensor wiring harness
is not twisted more than 180 degrees and is not in contact
with either the exhaust or driveshaft.
NOTE: If the original sensor is to be installed, apply
lubricant meeting specification ESE-M12A4-A to the thread
of the sensor.
Torque: 45 Nm
2. NOTE: Install a new gasket.
Special Tool(s): 303-1444-01
Page 973 of 3039
3. NOTE: If a new cylinder head is installed use the
special tools in the illustration.
Special Tool(s): 303-1444-02
4. CAUTION: Make sure that new bolts are installed.
NOTE: Install the spacers in the noted position.
Torque: 10 Nm
5. Remove the special tool.
6. CAUTION: Make sure that new bolts are installed.
NOTE: Install the spacers in the noted position.
Torque: 10 Nm
Page 974 of 3039
7.
8.
9.
10. Torque: 18 Nm
Torque: 100 Nm
WARNING: Make sure that a new bolt is installed.
NOTE: Some variation in the illustrations may occur,
but the essential information is always correct.
Torque: 35 Nm
Page 975 of 3039
Torque: 10 Nm
Torque: 3 Nm
Page 978 of 3039
5.
6.
All vehicles
7.
CAUTION: Discard the bolt.
Torque: 35 Nm
Torque: 100 Nm
Torque: 12 Nm
Page 979 of 3039
8.
9.
10.
11. Torque: 48 Nm
CAUTIONS:
Discard the bolts.
LH illustration shown, RH is similar.
NOTES:
Discard the gasket.
Make sure that the position of the spacers is noted
before removal of the manifold.
Page 980 of 3039
Installation
12.
NOTE: Do not disassemble further if the component is
removed for access only.
All vehicles
1. Torque: 45 Nm 2. CAUTION: LH illustration shown, RH is similar.
NOTE: Install a new gasket.
Install the special tool.
Special Tool(s): 303-1444-01
Page 981 of 3039
3. CAUTION: LH illustration shown, RH is similar.
NOTE: If a new cylinder head is installed use the
special tools in the illustration.
Install the special tool.
Special Tool(s): 303-1444-02
4. CAUTIONS:
Make sure that new bolts are installed.
LH illustration shown, RH is similar.
NOTE: Install the spacers in the noted position.
Torque: 10 Nm
5. CAUTION: LH illustration shown, RH is similar.
Remove the special tool.
6. CAUTIONS:
Make sure that new bolts are installed.
LH illustration shown, RH is similar.
NOTE: Install the spacers in the noted position.
Torque: 10 Nm www.JagDocs.com
Page 982 of 3039
7.
8.
9.
10. CAUTION: LH illustration shown, RH is similar.
Torque: 18 Nm
Torque: 12 Nm
Page 983 of 3039
11. Torque: 48 Nm
Right-hand drive vehicles
12.
13.
CAUTION: Discard the bolt.
Torque: 35 Nm
Torque: 100 Nm