INFINITI QX56 2011 Factory Service Manual

CCS-6
< PRECAUTION >[ICC]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint S
ystem (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006224261
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and w hether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISS AN/INFINITI dealer.
 Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
 Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
 When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
 When using air or electric power tools or hammers , always switch the ignition OFF, disconnect the
battery, and wait at least 3 minu tes before performing any service.
Precautions For Harness RepairINFOID:0000000006224262
ITS communication uses a twisted pair line. Be careful when repairing it.
 Solder the repaired area and wrap tape around the soldered area.
NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).
SKIB8766E
Revision: 2010 May2011 QX56

CCS
PRECAUTIONSCCS-7
< PRECAUTION > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
 Bypass connection is never allowed at the repaired area. NOTE:
Bypass connection may cause ITS communication error. The
spliced wire becomes separated and t he characteristics of twisted
line are lost.
ICC System ServiceINFOID:0000000006224263
CAUTION:
 Never look straight into th e laser beam discharger when adjusting laser beam aiming.
 Turn the MAIN switch OFF in conditions similar to driving, such as free rollers or a chassis dyna-
mometer.
 Never use the ICC sensor removed from vehicle. Never disassemble or remodel.
 Erase DTC when replacing parts of ICC system, then check the operation of ICC system after adjust-
ing laser beam aiming if necessary.
SKIB8767E
Revision: 2010 May2011 QX56

CCS-8
< PREPARATION >[ICC]
PREPARATION
PREPARATION
PREPARATION
Special Service ToolsINFOID:0000000006224264
The actual shapes of Kent-Moore tools may differ fr
om those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name Description
KV99110100
(J-45718)
ICC target board Uses for laser beam aiming adjustment
PKIA0358J
Revision: 2010 May2011 QX56

CCS
COMPONENT PARTSCCS-9
< SYSTEM DESCRIPTION > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000006224265
1. ICC steering switch 2. Information display, ICC system warning lamp, IBA OFF indicator
lamp, buzzer
(On the combination meter)3. BCM
Refer to BCS-4, "
BODY CONTROL
SYSTEM : Compon ent Parts Loca-
tion"
4. Transfer control unit
Refer to DLN-10, "
Component Parts
Location"
5. ICC brake hold relay 6. ECM
Refer to EC-16, "
Component Parts
Location"
7. ICC sensor 8. TCM
Refer to TM-10, "
A/T CONTROL
SYSTEM : Compon ent Parts Loca-
tion"
9. ABS actuator and electric unit (con-
trol unit)
Refer to BRC-10, "
Component Parts
Location"
10. Stop lamp switch 11. ICC brake switch 12. IBA OFF switch
JSOIA0362ZZ
Revision: 2010 May2011 QX56

CCS-10
< SYSTEM DESCRIPTION >[ICC]
COMPONENT PARTS
Component Description
INFOID:0000000006224266
× : Applicable
13. Steering angle sensor
Refer to BRC-10, "
Component Parts
Location"
14. ADAS control unit
Refer to DAS-13, "
Component Parts
Location"
A. Back side of engine room (RH) B. Front bumper (center) C. Upper side of brake pedal
D. Under side of inst rument lower driver
panel
Component Function
Description
Vehicle-to-vehicle distance control mode
Conventional (fixed speed) cruise control mode Intelligent Brake Assist (IBA)
Brake Assist (with preview function)
ADAS control unit ×××× ADAS control unit calculates a target distance between vehicles
and a target speed, based on signals received from each sensor
and switch to transmit an engine torque command value to ECM
and a brake fluid pres sure control signal to ABS actuator and
electric unit (control unit) via CAN communication
 ADAS control unit transmits buzzer output signal to combination
meter via CAN communication
ICC sensor ×××× ICC sensor detects light reflected from a vehicle ahead by irra-
diating laser forward and calculates a distance from the vehicle
ahead and a relative speed, based on the detected signal
 ICC sensor transmits the presence/absence of vehicle ahead and the distance from the vehicle to ADAS control unit via ITS
communication
ECM ×××× ECM transmits the accelerator pedal position signal, ICC brake
switch signal, stop lamp switch signal, ICC steering switch sig-
nal, etc. to ADAS control unit via CAN communication
 ECM controls the electric throttle control actuator based on the engine torque demand received from the ADAS control unit via
CAN communication
ABS actuator and electric unit
(control unit) ×××× ABS actuator and electric unit (control unit) transmits the vehicle
speed signal (wheel speed), stop lamp signal and VDC/TCS/
ABS system operation condition to ADAS control unit via CAN
communication
 ABS actuator and electric unit (control unit) controls the brake, based on a brake fluid pressure control signal received from the
ADAS control unit via CAN communication
BCM ×BCM transmits the front wiper request signal to ADAS control unit
via CAN communication
TCM ××TCM transmits the signal related to A/T control to ADAS control
unit via CAN communication
Revision: 2010 May2011 QX56

CCS
COMPONENT PARTSCCS-11
< SYSTEM DESCRIPTION > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
NOTE:
Only IBA system uses
Combination meter ××××Performs the following operations using the signals received from
the ADAS control unit via the CAN communication
 Displays the ICC system operation status using the meter dis-
play signal
 Illuminates the ICC system warning lamp using the ICC warning
lamp signal
 Illuminates the IBA OFF indicator lamp using the IBA OFF indi- cator lamp signal
 Operates the buzzer (ICC warning chime) using the buzzer out- put signal
ICC steering switch ×× ICC steering switch allows the ON/OFF of the Intelligent Cruise
Control and the settings of a vehicle speed and distance be-
tween vehicles
 ICC steering switch signal is transmitted to ECM. ECM transmits the signal to the ADAS control unit via CAN communication
ICC brake switch ×××× ICC brake switch is turned OFF and stop lamp switch is turned
ON, when depressing the brake pedal
 ICC brake switch signal is input to ECM. These signals are transmitted from ECM to ADAS control unit via CAN communi-
cation
 Stop lamp switch signal is in put to ECM and ABS actuator and
electric unit (control unit). These signals are transmitted from
ECM and ABS actuator and electric unit (control unit) to ADAS
control unit via CAN communication
Stop lamp switch
××××
ICC brake hold relay ××ICC brake hold relay activates the stop lamp by ICC brake hold re-
lay drive signal (stop lamp drive signal) outputted by the ADAS
control unit
Transfer control unit ××××Transfer control unit transmits a mode selection state of 4WD shift
switch to the ADAS control unit via CAN communication
IBA OFF switch ×
NoteIBA OFF switch signal is input to the ADAS control unit
Steering angle sensor ×Measures the rotation amount, rotation speed, and rotation direc-
tion of steering wheel, and then transmits them to ADAS control
unit via CAN communication
Component
Function
Description
Vehicle-to-vehicle distance control mode
Conventional (fixed speed) cruise control mode Intelligent Brake Assist (IBA)
Brake Assist (with preview function)
Revision: 2010 May2011 QX56

CCS-12
< SYSTEM DESCRIPTION >[ICC]
SYSTEM
SYSTEM
System DescriptionINFOID:0000000006224267
SYSTEM DIAGRAM
ADAS CONTROL UNIT INPU
T/OUTPUT SIGNAL ITEM
Input Signal Item
JSOIA0289GB
Revision: 2010 May2011 QX56

CCS
SYSTEMCCS-13
< SYSTEM DESCRIPTION > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
Transmit unit Signal name Description
ECM CAN com-
munica-
tionClosed throttle position signal Receives idle position state (ON/OFF)
Accelerator pedal position signal Receives accelerator pedal position (angle)
ICC prohibition signal
Receives an operable/inoperable state of the ICC sys-
tem
ICC steering switch
signal Main switch signal
Receives the operational state of the ICC steering
switch
SET/COAST switch
signal
CANCEL switch sig-
nal
RESUME/ACCEL-
ERATE switch signal
DISTANCE switch
signal
Engine speed signal Receives engine speed
Stop lamp switch signal Receives an operational state of the brake pedal
ICC brake switch signal Receives an operational state of the brake pedal
Snow mode signal Receives an operational state of the snow mode
TCM CAN com-
munica-
tionInput speed signal Receives the number of revolutions of input shaft
Current gear position signal Receives a current gear position
Shift position signal Receives a selector lever position
Output shaft revolution signal Receives the number of revolutions of output shaft
ABS actuator
and electric unit
(control unit) CAN com-
munica-
tionABS malfunction signal Receives
a malfunction state of ABS
ABS operation signal Receives an operational state of ABS
ABS warning lamp signal Receives an ON/OFF state of ABS warning lamp
TCS malfunction signal Receives a malfunction state of TCS
TCS operation signal Receives an operational state of TCS
VDC OFF switch signal Receives an ON/OFF state of VDC
VDC malfunction signal Receives a malfunction state of VDC
VDC operation signal Receives an operational state of VDC
Vehicle speed signal (ABS) Receives wheel speeds of four wheels
Stop lamp switch signal Receives an operational state of the brake pedal
Yaw rate signal Receives yaw rate acting on the vehicle
Combination
meter CAN com-
munica-
tion
Parking brake switch signal Receives an operational state of the parking brake
BCM CAN com-
munica-
tion
Front wiper request signal Receives an operational state of front wiper(s)
Steering angle
sensor CAN com-
munica-
tionSteering angle sensor malfunction signal Receives a malfunction state of steering angle sensor
Steering angle sensor signal
Receives the number of revolutions, turning direction of
the steering wheel
Steering angle speed signal Receives the turning angle speed of the steering wheel
Transfer control
unit CAN com-
munica-
tion
Current 4WD mode signal Receives a mode selection state of the 4WD mode
Revision: 2010 May2011 QX56

CCS-14
< SYSTEM DESCRIPTION >[ICC]
SYSTEM
Output Signal Item
DESCRIPTION
Intelligent Cruise Control
The Intelligent Cruise Control (ICC) system maintains a se
lected distance from the vehicle in front of own vehi-
cle within the speed range of 0 to 144 km/h (0 to 90 MPH) up to the set speed.
The set speed can be selected by the driver between 32 to 144 km/h (20 to 90 MPH).
The vehicle travels at a set speed when the road ahead is clear.
The ICC system can be set to one of two cruise control modes:
CAUTION:
Never set the cruise speed exceed ing the posted speed limit.
Vehicle-to-vehicle Distance Control Mode
ICC sensorITS com-
munica-
tionICC sensor signal
Receives detection results, such as the presence or ab-
sence of a leading vehicle and distance from the vehicle
IBA OFF switch IBA OFF switch signal Receives an ON/OFF state of the IBA OFF switch Transmit unit Signal name Description
Reception unit Signal name Description
ECM CAN commu-
nicationICC operation signal
Transmits an ICC operation signal necessary for Intel-
ligent Cruise Control
TCM CAN commu-
nicationICC operation signal Transmits an ICC operation signal necessary for Intel-
ligent Cruise Control via ECM
ABS actuator
and electric
unit (control
unit) CAN commu-
nication
Brake fluid pressure control signal
Transmits a brake fluid pressure control signal to acti-
vates the brake
Combination
meter CAN commu-
nicationMeter display
signal Own vehicle indicator
signal
Transmits a signal to display a state of the system on
the information display
Vehicle ahead detec-
tion indicator signal
Set vehicle speed indi-
cator signal
Set distance indicator
signal
SET switch indicator
signal
MAIN switch indicator
signal
ICC warning lamp signal Transmits an ICC warning lamp signal to turn ON the
ICC system warning lamp
IBA OFF indicator lamp signal  Transmits a signal to turn ON the IBA OFF indicator
lamp
 Transmits an ON/OFF state of the intelligent brake
assist
Buzzer output signal Transmits a buzzer output signal to turn ON the buzz-
er of the following systems:
 Intelligent Cruise Control (ICC)
 Intelligent Brake Assist (IBA)
ICC sensor ITS commu-
nication
Vehicle speed signal Transmits a vehicle speed calculated by the ADAS
control unit
ICC brake hold
relay ICC brake hold relay drive signal
Activates the brake hold relay and turns ON the stop
lamp
Revision: 2010 May2011 QX56

CCS
SYSTEMCCS-15
< SYSTEM DESCRIPTION > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
For maintaining a selected distance between own vehicle and the vehicle in front of own vehicle up to t\
he pre-
set speed. Refer to CCS-15, "
VEHICLE-TO-VEHICLE DISTANCE CO NTROL MODE FUNCTION : System
Description".
Conventional (Fixed Speed) Cruise Control Mode
For cruising at a preset speed. Refer to CCS-18, "CONVENTIONAL (FIXED SPEED) CRUISE CONTROL
MODE FUNCTION : System Description".
NOTE:
In the Conventional (Fixed Speed) Cruise Control Mode, a warning chime will not sound to warn driver if own
vehicle are too close to the vehicle ahead.
WARNING:
Always drive carefully and attentively when using ei ther cruise control mode. To avoid serious injury
or death, do not rely on the system to prevent accide nts or to control the vehicle's speed in emer-
gency situations. Do not use cr uise control except in appropriat e rode and traffic conditions.
Distance Control Assist (DCA) System
DCA share the systems and component s with ICC system. Refer to DAS-68, "System Description".
Forward Collision Warning (FCW) System
FCW share the systems and component s with ICC system. Refer to DAS-218, "System Description".
Intelligent Brake Assist (IBA) System
IBA system share the systems and components with ICC system. Refer to BRC-152, "INTELLIGENT BRAKE
ASSIST : System Description".
Brake Assist (with preview function)
Brake Assist (with preview function) share t he systems and components with ICC system. Refer to BRC-145,
"BRAKE ASSIST (WITH PREVIEW FUNCTION) : System Description".
Fail-safe (ADAS Control Unit)INFOID:0000000006224268
If a malfunction occurs in each system, ADAS control unit cancels eac h control, sounds a beep, and turns ON
the warning lamp or indicator lamp.
Fail-safe (ICC Sensor)INFOID:0000000006224269
If a malfunction occurs in the ICC sensor, ADAS cont rol unit cancels control, sounds a beep, and turns ON the
ICC system warning lamp in the combination meter.
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE FUNCTION
VEHICLE-TO-VEHICLE DISTANCE CONTRO L MODE FUNCTION : System Descrip-
System Buzzer Warning lamp/Indicator lamp Description
Vehicle-to-vehicle distance control mode High-pitched
toneICC system warning lamp Cancel
Conventional (fixed speed) cruise control mode High-pitched
tone
ICC system warning lamp Cancel
Intelligent Brake Assist (IBA) High-pitched
toneIBA OFF indicator lamp Cancel
Forward Collision Warning (FCW) High-pitched
toneIBA OFF indicator lamp Cancel
Distance Control Assist (DCA) High-pitched
tone
ICC system warning lamp Cancel
Lane Departure Warning (LDW) — Lane departure warning lamp Cancel
Lane Departure Prevention (LDP) Low-pitched
toneLane departure warning lamp Cancel
Blind Spot Warning (BSW) — BSW warning lamp Cancel
Revision: 2010 May2011 QX56