key ISUZU TROOPER 1995 Owner's Manual

4-WHEEL ANTILOCK BRAKE SYSTEM (ABS) 5A4-21
MODE F5: ACTUATOR TEST
This mode is used to exercise the ABS system actuators and make sure they operate normally. Prior to the
test, pay attention
to the cautions below. (When checking the solenoid valve system, be sure to jack up the
vehicle.)
w CAUTION:
• Before testing, be sure that the brakes work normally.
• Make sure that the battery is fully charged.
Conduct the test
by two persons (A TECH 1 operator and a vehicle checker).
• Be sure to start actuator test with the engine stopped.
• Before testing, make sure that electrical trouble, if any, has been completely repaired. Conducting
tests
of ABS actuator with electrical circuit problem remaining uncorrected could damage the
control unit.
Selection Procedure:
SELECT MODE FO:DATA LIST
*
F5:ACTUATOR TEST
IUiJ
SELECT ACTUATOR * P. MOTOR RELAY FL SOL. VALVE
FR SOL. VALVE REAR SOL. VALVE
ABS W/L
----> Refer to CD
----> Refer to ®
----> Refer to @ ----> Refer to @
----> Refer to ®
NOTE:
F5; Actuator test procedure, the systems Q) to @
mentioned on the left can be checked four times
continuously as each system is checked once.
When checking more than
four times continuously,
the fifth check
must be started with a break of 10
minutes or more after the fourth to protect ABS
pump motor.
Select the desired test
by operating !I] 1[!] keys and press I ENT I key.

5A4-22 4-WHEEL ANTI LOCK BRAKE SYSTEM (ABS)
(j): Pump Motor Relay Test
The pump motor operates when current flows through the pump motor relay coil (Fig. 5A4-9).
PUMP
MOTOR
~ II
....----
EBCM ~ .____
MOTOR RELAY
Fig. 5A4-9
Confirm the operation of the pump motor by its operating sound in the engine compartment.
TECH 1 Display Key Operation
Display 1 Is the pump motor working ? If so, press the YES key. If not, press the NO
key. (The pump motor works for about 5 seconds.)
P.MOTOR RELAY
COMMANDED ON * If the YES key is pressed, the menu display will be returned.
OKAY ?
(YES/NO)
If the NO key was pressed above
Display 2
A test failure.
The pump motor has mechanical trouble.
P.MOTOR RELAY
TEST FAILED * If the YES key is pressed, the menu display will be returned.
(YES)
If the YES or NO key was not pressed within 5 sec. on Display 1 above
Display 3
Did the pump motor work normally?
If so, press the YES key. If not, press the NO key.
P.MOTOR RELAY
OKAY ? * YES key c:::> Menu display
(YES/NO) *No key c:::>Display 2
•

5A4-24 4-WHEEL ANTILOCK BRAKE SYSTEM (ABS)
®: Front left wheel brake system test
TECH 1 Display
Key Operation Brake
pedal
BEFORE TEST RUN • Prior to the test, be sure to understand the entire OFF ON
SEE CHECKING procedure.
PROCEDURE • To go to the next step, press the YES key.
(YES)
FL SOL. VALVE Can the wheel be turned by hand?
NORMAL FUNCTION If so, press the YES key. Of not, press the NO key. (lfthe NO
WHEEL TURNABLE ? key is pressed, Diaplay 1 will be returned.)
(YES/NO)
FL SOL. VALVE Depress the brake pedal. Hold it down through the rest of
NORMAL FUNCTION this test.
DEPRESS AND HOLD
BRAKE PEDAL !
FL SOL. VALVE Is the wheel locked ?
NORMAL FUNCTION If so, press the YES key. If not, press the NO key. (If the NO
WHEEL BLOCKED ? key is pressed, Display 1 will be returned.)
(YES/NO)
FL SOL. VALVE The TECH 1 commands the EBCM to reduce hydraulic
RELEASE FUNCTION pressure and activate the pump motor. Display
p. MOTOR RELAY automatically goes to next display after a few seconds.
Brake pressure has been reduced. Can the wheel be turned
FL SOL. VALVE by hand ? If so, press the YES key. If not, press the NO key.
RELEASE FUNCTION (If the NO key is pressed, Display 2 will be returned.)
WHEEL TURNABLE ? Note:
(YES/NO) To protect the valve, press the YES or NO key within 10
seconds.
FL SOL. VALVE With the solenoid valve released, brake pedal pressure is
RELEASE FUNCTION allowed to reach the brake.
WHEEL BLOCKED ? Is the wheel locked ? If so, press the YES key. If not, press
(YES/NO) the NO key. (If the NO key is pressed, Display 2 will be
returned.)
(Test is over.)
•

4-WHEEL ANTILOCK BRAKE SYSTEM (ABS) 5A4-25
TECH 1 Display Key Operation
Display 1 There is some problem in the normal hydraulic/mechanical brake system
(not
ABS problem).
FL SOL. VALVE Check the brake piping system.
NORMAL FUNCTION If the YES is pressed, the Menu Display will be returned.
TEST FAILED !
(YES)
Display 2 It is suspected that there is a mechanical abnormality in the related brake
piping.
Please check.
FL SOL. VALVE Press YES key, and MENU will return.
RELEASE FUNCTION
TEST FAILED !
C YES)

5A4-26 4-WHEEL ANTILOCK BRAKE SYSTEM (ABS)
@: Front right wheel brake system test
TECH 1 Display
Key Operation Brake pedal
BEFORE TEST RUN • Prior to the test, be sure to understand the entire OFF ON
SEE CHECKING procedure.
PROCEDURE • To go to the next step, press the YES key.
(YES)
FR SOL. VALVE Can the wheel be turned by hand ?
NORMAL FUNCTION If so, press the YES key. Of not, press the NO key. (If the NO
WHEEL TURNABLE ? key is pressed, Diaplay 1 will be returned.)
(YES/NO)
FR SOL. VALVE Depress the brake pedal. Hold it down through the rest of
NORMAL FUNCTION this test.
DEPRESS AND HOLD
BRAKE PEDAL !
FR SOL. VALVE Is the wheel locked ?
NORMAL FUNCTION If so, press the YES key. If not, press the NO key. (If the NO
WHEEL BLOCKED ? key is pressed, Display 1 will be returned.)
(YES/NO)
FR SOL. VALVE The TECH 1 commands the EBCM to reduce hydraulic
RELEASE FUNCTION pressure and activate the pump motor. Display
P. MOTOR RELAY automatically goes to next display after a few seconds.
Brake pressure has been reduced.
Can the wheel be turned
FR SOL. VALVE by hand? If so, press the YES key. If not, press the NO key.
RELEASE FUNCTION (If the NO key is pressed, Display 2 will be returned.)
WHEEL TURNABLE ? Note:
(YES/NO) To protect the valve, press the YES or NO key within 10
seconds.
FR SOL. VALVE With the solenoid valve released, brake pedal pressure is
RELEASE FUNCTION allowed to reach the brake.
WHEEL BLOCKED ? Is the wheel locked? If so, press the YES key. If not, press
(YES/NO) the NO key. (If the NO key is pressed, Display 2 will be
returned.)
(Test is over.)
•

4-WHEEL ANTI LOCK BRAKE SYSTEM (ABS) 5A4-27
TECH 1 Display Key Operation
Display 1 There
is some problem in the normal hydraulic/mechanical brake system
(not
ABS problem).
FR SOL. VALVE Check the brake piping system.
NORMAL FUNCTION If the YES is pressed, the Menu Display will be returned.
TEST FAILED
!
(YES)
Display 2 It is suspected that there is a mechanical abnormality in the related brake
piping. Please check.
FR SOL. VALVE Press YES key, and MENU will return.
RELEASE FUNCTION
TEST FAILED
!
(YES)

5A4-28 4-WHEEL ANTILOCK BRAKE SYSTEM (ABS)
@: Rear wheel brake system test
TECH 1 Display
Key Operation Brake
pedal
BEFORE TEST RUN • Prior to the test, be sure to understand the entire OFF ON
SEE CHECKING procedure.
PROCEDURE • To go to the next step, press the YES key.
(YES)
REAR SOL. VALVE Can the wheel be turned by hand ?
NORMAL FUNCTION If so, press the YES key. Of not, press the NO key. (If the NO
WHEEL TURNABLE ? key is pressed, Diaplay 1 will be returned.)
(YES/NO)
REAR SOL. VALVE Depress the brake pedal. Hold it down through the rest of
NORMAL FUNCTION this test.
DEPRESS AND HOLD
BRAKE PEDAL !
REAR SOL. VALVE Is the wheel locked ?
NORMAL FUNCTION If so, press the YES key. If not, press the NO key. Of the NO
WHEEL BLOCKED ? key is pressed, Display 1 will be returned.)
(YES/NO)
REAR SOL. VALVE The TECH 1 commands the EBCM to reduce hydraulic
RELEASE FUNCTION pressure and activate the pump motor. Display
P. MOTOR RELAY automatically goes to next display after a few seconds.
Brake pressure has been reduced. Can
the wheel be turned
REAR SOL. VALVE by hand ? If so, press the YES key. If not, press the NO key.
RELEASE FUNCTION (If the NO key is pressed, Display 2 will be returned.)
WHEEL TURNABLE ? Note:
(YES/NO) To protect the valve, press the YES or NO key within 10
seconds.
REAR SOL. VALVE With the solenoid valve released, brake pedal pressure is
RELEASE FUNCTION allowed to reach the brake.
WHEEL BLOCKED ? Is the wheel locked ? If so, press the YES key. If not, press
(YES/NO) the NO key. (If the NO key is pressed, Display 2 will be
returned.)
(Test is over.)
•

4-WHEEL ANTILOCK BRAKE SYSTEM (ABS) 5A4-29
TECH 1 Display
Key Operation
Display 1
There is some
problem in the normal hydraulic/mechanical brake system
(not
ABS problem).
REAR SOL. VALVE Check the brake piping system.
NORMAL FUNCTION lfthe YES is pressed, the Menu Display will be returned.
TEST FAILED !
(YES)
Display 2 It is suspected that there is a mechanical abnormality in the related brake
piping. Please check.
REAR SOL. VALVE Press YES key, and MENU will return.
RELEASE FUNCTION
TEST FAILED !
(YES)

5A4-30 4-WHEEL ANTILOCK BRAKE SYSTEM (ABS)
@: ABS
warning light test
In this test, light is actuated to make sure of its function (Fig. 5A4-10).
Fig. 5A4-10
TECH 1 Display
Key Operation
Is the light blinking ? ABS W/L * BLINK If so, press the YES key. If not, press the NO key.
OKAY ?
(YES/NO)
If
fault exists and the NO key is pressed
A test failure.
TEST FAILED Check ABS W/L wiring and
fuses.
(YES)
i _______________________________________________________________________ \
! •

5A4-32 4-WHEEL ANTI LOCK BRAKE SYSTEM (ABS)
TECH 1 Display Key Operation
INSTRUCT I ON: This explains MODE F6.
DRIVE VE-Drive vehicle at 20 km/h (12 mph).
HICLE AT 20km/h Press the YES key for the next display.
AND THEN (YES)
RELEASE GAS Release accelerator pedal while driving, and put transmission into neutral.
PEDAL, DISENGAGE Press the YES key for the next display.
TRANSMISSION
AND (YES)
AS SOON AS THE After coasting to a halt with transmission in neutral, apply brakes
VEHICLE HAS immediately.
STOPPED APPLY Press the YES key for the next display.
BRAKES (YES) This completes instructions as to F6.
The test will be started with the next display.
BEGIN TEST Let's begin the test.
DRIVE VE-Carry out the test according to the display.
HICLE AT 20km/h ** indicates the wheel speed value into which the output of each sensor ** ** ** ** has been converted.
Decelerate vehicle by coasting until it comes to a halt. (Parking brake may
DECREASE VEHICLE be slightly engaged.)
SPEED TO Okm/h
** ** ** **
MEASURED WHEEL Make sure that there is no significant difference among the wheel speed
SPEED THRESHOLDS values.
** **
** ** The
data indicate 3-5 km/h (2-3 mph).
SEE CHART 6 (YES) See CHART 6 .. Refer to CHART C-2 for check procedure.
To obtain mph in
MODE: F6, display mph in MODE: FO once and thereafter, change to MODE:F6.