ISUZU KB P190 2007 Workshop Repair Manual

REAR AXLE 4B-7
REAR AXLE ASSEMBLY
General Description
A03R300001

The rear axle assembly is of the semi–floating type in
which the vehicle weight is carried on the axle
housing .
The center line of the pinion gear is below the cente
r
line of the ring gear (hypoid drive).
All parts necessary to transmit power from the
propeller shaft to the rear wheels are enclosed in a
banjo type axle housing.
The φ220 mm (8.6 in) or φ194mm (7.6 in) ring gea
r
rear axle uses a conventional ring and pinion gear set
to transmit the driving force of the engine to the rea
r
wheels. This gear set transfers this driving force at a
90 degree angle from the propeller shaft to the drive
shafts.
The axle shafts are supported at the wheel end of the
shaft by a double tapered roller bearing.
The pinion gear is supported by two tapered rolle
r
bearings. The pinion depth is set by a shim pack
located between the gear end of the pinion and the
roller bearing that is pressed onto the pinion. The
pinion bearing preload is set by crushing a collapsible
spacer between the bearings in the axle housing.
The ring gear is bolted onto the differential cage with
12 bolts.
The differential cage is supported in the axle housing
by two tapered roller bearings. The differential and ring
gear are located in relationship to the pinion by using
selective shims and spacers between the bearing and
the differential cage. To move the ring gear, shims are
deleted from one side and an equal amount are added
to the other side. These shims are also used to
preload the bearings, which are pressed onto the
differential cage. Two bearing caps are used to hold
the differential into the rear axle housing.
The differential is used to allow the wheels to turn at
different rates of speed while the rear axle continues
to transmit the driving force. This prevents tire
scuffing when going around corners and prevents
premature wear on internal axle parts.
The rear axle is sealed with a pinion seal, a seal at
each axle shaft end, and by a liquid gasket between
the differential carrier and the axle housing.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4B-8 REAR AXLE
SERVICING
Rear Axle Oil Replacement
Oil Capacity liters (US/UK gal.)

Specified gear oil GL5 (API grade)(STD)
GL5LSD (LSD)

φ220mm 2.4 (0.63/0.53)
φ194mm 1.6 (0.42/0.35)
Filler Plug and Drain Plug Torque N ⋅m (kgf ⋅m/lb ⋅ft)
78 (8.0/58)

Axle Shaft Roller Bearing Endplay
Inspection
1. Raise and suitably support vehicle.
2. Remove the wheel and brake drum.
3. Inspect the axle shaft roller bearing endplay using dial gauge.
Endplay mm (in
)
Standard 0 ~ 0.2 (0 ~ 0.008)
If the endplay exceeds 0.2mm (0.008 in), replace the
axle shaft roller bearings.
Refer to Rear Axle Reassembly.

RTW 34BSH000101


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

REAR AXLE 4B-9
REAR AXLE
1. Refer to Section 3E “W HEELS and TIRES” for
road wheel Disassembly procedure.
2. Refer to Section 5 “BRAKE” for rear brake removal procedure.





RTW 54BLF000401
Legend
1. Brake Drum
2. Bolt and Nut
3. Axle Shaft Assembly with Brake
4. Shim
5. Snap Ring
6. Axle Shaft
7. Retainer (with ABS)
Retainer (without ABS)
8. Double Taper Roller Bearing

9. Oil Seal
10. Bearing Holder
11. Rear Brake
12. Bolt and Nut
13. Differential Assembly
14. Rear Axle Case Assembly
15. W heel Pin
16. Axle Case Oil Seal
17. Front

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4B-10 REAR AXLE
Disassembly
• Raise vehicle to the working level.
• Support the axle assembly with the proper jack
and chassis stands.
• Remove wheel and tire.
• Drain differential oil.
• Remove propeller shaft. (Refer to the section
“Rear Propeller Shaft”.)

1. Remove brake drum.
2. Remove ABS sensor. (Refer to the section “ABS”.)
3. Remove brake pipe from wheel cylinder.

420R300003



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

REAR AXLE 4B-11
305R30000
Legend
1. Tension Pin
2. Shoe Clamp Spring
3. Return Spring
4. Shoe Assembly with Parking Brake Lever
5. Shoe Assembly with Adjuster Lever
6. Spring
7. Parking Brake Cable


8. Adjuster
9. Parking Brake Lever
10. Adjuster Spring
11. Adjuster Lever
12. W heel Cylinder
13. Back plate


4. Remove tension pin and shoe clamp spring.
5. Remove return spring.
6. Remove shoe assembly with parking brake lever.
7. Remove shoe assembly with adjuster lever and spring.
8. Remove parking brake inner cable from parking
brake lever.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4B-12 REAR AXLE
9. Use offset box wrench to compress locking lugs
on the cable, then remove parking brake oute
r
cable from back plate.

311RS012
Legend
1. Offset Box W rench


10. Remove wheel cylinder.
11. Remove bearing holder fixing nuts.
12. Take out axle shaft assembly with back plate and
set it on a bench press as following illustration.
W hen axle shaft is extracted, since axle case oil
seal is damaged, replace the axle case oil seal.
13. Remove snap ring. Use snap ring pliers to
remove. Snap ring is prohibition of reuse.
14. Remove shim (If so equipped)
15. Grind the retainer surfaces using a grinder, then chisel them out with a chisel.



16. Position remover 5-8840-2831-0 on the bearing
holder with 4 nuts.




RTW 54BSH000801


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

REAR AXLE 4B-13
17. Remove double taper roller bearing, oil seal,
bearing holder, and back plate from axle shaft b
y
means of a press.
• Discard used oil seal, double taper rolle
r
bearing, snap ring, retainer.




RTW 54BMH000201
Legend
1. Bench Press Fitting
2. Axle Shaft


18. Oil seal is removed from bearing holder.

19. Bearing outer race is removed from bearing
holder.
• W hen it cannot remove by hand, bearing
outer race is removed using installer 5-8840-
2119-0 and grip 5-8840-0007-0.




RTW 54BSH000701
20. Remove differential assembly fixing bolts and
nuts and take out differential assembly.
• φ 194mm differential assembly has three kinds
of bolts.
Note the installation holes.
21. Remove wheel pin from axle shaft, using the
remover 5-8840-0079-0.
420L100009
22. Remove axle case oil seal.
• Discard used oil seal.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4B-14 REAR AXLE
Inspection and Repair
Make all necessary adjustments, repairs, and part
replacements if wear, damage, or other problems are
discovered during inspections.
Visual Check
Inspect the following parts for wear, damage or other
abnormal conditions.
• Axle Shaft
Axle Shaft
W hen checking the axle shaft, pay special attention to
the splined portions and replace the shaft if distortion
or step wear is noticeable. Correct slight step wea
r
with a pencil grinder.




420RS008
Axle Shaft Run-Out
Check the shafts for bending with the use of a dial
indicator in contact with the shaft. Rotate the shaft
slowly and observe the dial indicator.
Limit mm (in
)
1.0 (0.039)
Note :
Never use heat to correct bending.











RTW 74BSH000101
Legend
a. 350 mm (13.8 in)

Axle Shaft Flange Run-Out
Check the axle shaft flange for run-out. Hold the
probe of a dial indicator in contact with the flange.
Rotate the shaft slowly and observe the dial.
Limit mm (in
)
0.08 (0.003)








RTW 74BSH000201
Legend
b. 160 mm (6.3 in)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

REAR AXLE 4B-15
Reassembly
1. Using the oil seal installer 5-8840-2202-0 and
grip 5-8840-0007-0, install new axle case oil seal.




RTW 54BSH000301

Note :
Confirm that the dimension : A should be 34.5 –
36.1 mm (1.36 – 1.42 in)







A03R300004

2. Install new oil seal in bearing holder, using the oil seal installer 5-8840-2404-0.






RTW 54BSH000501
Legend
1. Oil Seal
2. Bearing Holder


3. Drive wheel pin into axle shaft flange, using a hammer.
4. Differential assembly a. Clean the mating surface of axle case and differential carrier.
b.
Apply Three Bond 1215 (TB1215) or
equivalent on the surface of differential
assembly as flowing illustration.


RTW 74BSH000301
Legend
a. 3 mm (0.12 in)

c. Tighten bolts and nuts to the specified torque.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4B-16 REAR AXLE
φ
φφ
φ
220mm
Torque : Bolt 64 N ⋅m (6.5 kgf ⋅m/47 lb ⋅ft)
Nut 44 N ⋅m (4.5 kgf ⋅m/33 lb ⋅ft)
φ
φφ
φ
194mm
Torque : Bolt 25 N ⋅m (2.5 kgf ⋅m/18 lb ⋅ft)
Nut 37 N ⋅m (3.8 kgf ⋅m/27 lb ⋅ft)
5. Axle Shaft Assembly
a. Insert new double taper roller bearing in the bearing holder with oil seal.
b. Set special tool (support stand : 9-8522-1271- 0) on a bench press.
c. Put bearing holder with bearing and oil seal and back plate on the support stand as
following illustration.
d. Insert bolts and axle shaft, aligning center o
f
holes.
e. Press fit axle shaft into double taper rolle
r
bearing.




420R300010
Legend
1. Axle shaft
2. Oil Seal
3. Bolt
4. Back Plate
5. Double Taper Roller Bearing

6. Put new retainer on the special tool 9-8522-1271-
0.
7. Press fit axle shaft with the bearing into retaine
r
and make axle shaft assembly.




420R300011
Legend
1. Axle shaft
2. Oil Seal
3. Bolt
4. Back Plate
5. Retainer
6. Double Taper Roller Bearing



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007