JAGUAR X308 1998 2.G Workshop Manual
X308 1998 2.G
JAGUAR
JAGUAR
https://www.carmanualsonline.info/img/21/7640/w960_7640-0.png
JAGUAR X308 1998 2.G Workshop Manual
Trending: parking brake ORDER BY 10, transmission oil, body, parking brake ORDER BY 40, Starter relay, Starter motor, 303-14
Page 181 of 2490
5. Remove an
d discard the tie st
rap securing the wheel speed
sensor harness to the brake hose clip.
6. Mark the wi
shbone at the pivot
pin eccentric flange marker to
aid installation.
7. Remove the
pivot pin nut and washer.
8. CAUTION: To prevent damage to the parking brake cable,
the hub carrier must be supported on removal from the wishbone.
R
emove the hub carrie
r from the wishbone.
R
emove the pivot pin from the hub carrier.
Page 182 of 2490
Withdraw th
e hub carrier and support on a block of wood.
9. CAUTIO
N: Note the position of
the shims during removal.
They must be returned to th eir original position during
installation.
Noting their positions, remove the shim from each end of the
pivot pin sleeve.
10 . WAR
NINGS:
ENSURE THE SPECIAL TOOLS ARE POSITIONED
DIAMETRICALLY OPPOSITE ON THE SPRING AND THE ARMS ARE
CORRECTLY SEATED .
WHEN COMPRESSING THE SPRING, TIGHTEN THE
SPECIAL-TOOL ADJUSTMENT BOLTS EVENLY.
Compress the spring.
Install and alig n th
e special
tools 204-179 diametrically
opposite on the spring.
Eve n
ly tighten the special tool tensioning bolts to
compress the spring.
11 . R
emove the shock absorber to
wishbone mounting nut and
bolt.
12. Remove the nuts securing th e shock absorber and spring
upper mounting to the body.
Page 183 of 2490
13
.
Using the special tools 204-179-1, secure the upper mounting
to the spring.
14
.
Using a jack, retract the shock absorber through the
wishbone aperture.
15
.
Position a bolt through the spring coils and shock absorber
lower-bush, to temporarily locate the shock absorber.
16. Partially lower the jack for a ccess to the top of the shock
absorber.
17. On vehicles with adaptive damping:
Di
sconnect the shock absorber electrical connector by
pressing the lugs down and pulling the connector up.
Page 184 of 2490
18. Lower and remove the
jack.
19. Remove the shock absorber an d spring assembly from the
vehicle and place the assembly on a work bench.
20. Clean the upper mounting spring location.
21 . Remove the
pigtail seat and cl
ean the wishbone lower spring
location.
22 . W
ith assistance, manually compress the shock absorber and
withdraw the bolt from the spring coils.
23 . R
emove the shock absorber from the upper mounting.
Posi
ti
on a wrench on the shock absorber shaft flats to
prevent rotation (wrench in socket on vehicles with
adaptive damping).
R e
move the shock absorber
upper retaining nut.
Remove the u
pper washer and isolator.
24. Remove the special tools 204-179-1 and remove the upper
mounting from the spring.
Page 185 of 2490
I
nstallation
25
.
Remove the shock upper mounting assembly from the spring.
R
emove the spring
upper isolator.
Remove the
upper spring pan.
Remove the
packing ring.
1. Install th
e spring pigtail lower seat on to the wishbone.
2. Install
the spring in
the upper mounting.
Install
the spring upper isolator.
Install
the upper spring pan.
Inst
all the packing ring.
3. Ensuring the correct orientation, secure the upper mounting to
the spring using the special tools 204-179-1.
Page 186 of 2490
4. Position the spri ng
upper mounting assembly on to the shock
absorber.
Apply a th in
coat of grease to the upper mounting bush.
E
n
sure that the washer, lo
wer isolator and bush are
correctly positioned on the shock absorber shaft.
Po si
tion the shock absorber shaft in the upper mounting.
5. Sec
ure the top of the shock ab
sorber to the upper mounting.
Install the spri
ng upper isolator.
Inst
al
l the upper washer.
In
s
tall but do not tighten the locknut on to the shock
absorber.
6. Manu ally r
etract the shock abso
rber and place a bolt through
the spring coils and the sh ock absorber lower-bush.
7. Secure the shock absorber to the upper mounting.
Positi
on a wrench on the shock absorber shaft flats to
prevent rotation (wrench in socket on vehicles with
adaptive damping).
Tigh te
n the shock absorber upper lock nut to 30-40 Nm
(16-18 Nm on vehicles with adaptive damping).
Page 187 of 2490
8. Position the shock absorber and spri
ng assembly to the
vehicle.
9. W
ith assistance, manually re
tract the shock absorber and
remove the temporary securing bolt.
10
.
Remove the special tools 204-179-1.
11
.
Align the shock absorber lower bush to the wishbone and
install the mounting bolt.
1. Install but do not tighten the nut.
12. CAUTION: Make sure the adaptive damping electrical
connector is correctly aligned. Failu re to follow these instructions
may cause damage to the electrical connector.
On vehicles with adaptive damping:
Page 188 of 2490
Connect
the shock absorber elec
trical connector, ensuring
the electrical connector key locates in the socket keyway.
13. Seat
the upper mounting in the body location.
1. If adaptive damping is installed, ensure the harness is
correctly positioned.
14 . Ensuri
ng that the spri
ng is seated on the isolator and spring
pan, position the u pper spring pan on to the body studs.
15 . Re
lease the spring tension.
Ensuri
ng that the spri
ng is
correctly located, evenly
slacken the adjuster bolts on the special tools 204-179.
16. Remove the special tools 204-179.
17. Fully seat and secure the u pper spring pan to the body.
Ensure the spring pan i
s correctly seated in the body
location.
Inst al
l the nuts securing the sp
ring pan to the body studs.
Page 189 of 2490
Tigh
ten to 17-23 Nm.
18
.
Tighten to 80-100 Nm.
19
.
Install the shims on the pivot pin sleeve in the positions
noted during removal.
20
.
Install the hub assembly to the wishbone assembly.
Position the hub and carri
er to the wishbone.
Inst
all the pivot pin ensuring that the ecce
ntric flange
correctly seats in the wishbone groove.
21. Install the pivot pin nut.
Ali
gn the marker on the pivo
t pin flange with the mark
made on wishbone.
Inst
all the nut on to the pivot pin and, ensuring the pin
position is not dist urbed, tighten the nut to 88-118 Nm.
Page 190 of 2490
22. R
elease the tie strap securing the brake caliper to the
suspension mounting bracket.
23 . Install
the brake caliper on to the carrier.
1. Position the caliper asse mbly on to the carrier.
2. Install the guide pins and tighten to 25-30 Nm.
3. Install the dust caps.
4. Install the brake caliper spring clip.
24 . Conne
ct the wheel speed sensor electrical connector.
25 . U
sing a new tie strap, secure the wheel speed sensor harness
to the brake hose clip.
26. Install the rear wheel.
For additional informat ion, refer to Section 204
-04 W
heels and
Tire
s.
27 .
Remove the
axle stands
and lower the vehicle.
For additional informat ion, refer to Section 100
-02
Jacking and
Liftin
g.
Trending: timing belt, headlamps, Fuel pump relay, supercharger belt, Key transponder module, timing, radiator cap