MAZDA 626 1987 Workshop Manual

1 4 HEADLIGHT AND COMBINATION LIGHT
76G14X-007
86U14X-070
Removal Note
Turn signal light (Coupe/MX-6)
1. Remove the screws shown in the figure.
2. Disconnect the turn signal light connector.
3. Remove the turn signal light assembly.
Turn signal light (Sedan and Hatchback)
1. Remove the screws shown in the figure.
2. Disconnect the turn signal and parking light con-
nector.
3. Remove the turn signal and parking light assemble.
76G14X-008
14-30

HEADLIGHT AND COMBINATION LIGHT 1 4
AIMING
Headlight
1. Adjust the tires to the standard pressure.
2. Position the vehicle on a flat level surface (unload-
ed condition).
86U14X-073
76G14X-009
14-31

1 4 REAR COMBINATION LIGHTS
REAR COMBINATION LIGHTS
REMOVAL AND INSTALLATION
1. Disconnect the negative battery cable.
2. Remove in the sequence shown in the figure.
3. Install in the reverse order of removal.
76G14X-010
Hatchback
1. End trim
2. Nuts
3. Lens and body
4. Cover
5. Bulb: Turn signal light 21W
Brake and tail light 21W
Side marker light 5W
Sedan and Coupe/MX-6
1. End trim
2. Nuts
3. Lens and body
4. Cover
5. Bulb: Turn signal light 21W
Brake and tail light 21W
Side marker light 5W
14—32

REAR COMBINATION LIGHTS 1 4
REPLACEMENT OF REAR COMBINATION LIGHT
LENS
1. Use a hot air blower to soften the "hot melt" (bond-
ing agent) around the lens.
86U14X-077
2. Remove the lens from the light housing by push-
ing the rear of the lens with a hammer handle or
round bar.
76U14X-034
3. Heat the light housing, and remove the "hot melt"
and any fragments of the lens.
Note
a) The "hot melt" should be reused if
possible.
b) If the "hot melt" can be reused, the follow-
ing step is unnecessary.
86U14X-078
4. Put Uni-sealer (8531 77 739) adhesive in the light
housing groove.
86U14X-079
14—33

1 4 REAR COMBINATION LIGHTS
5. Fit the new lens onto the light housing. Press the
lens firmly so that it will adhere.
86U14X080
6. Immerse the combination light in water to check
for leaks.
76U14X-038
14—34

LICENSE PLATE
LIGHT
AND CORGO ROOM LIGHT
1
4
LICENSE PLATE LIGHT AND CORGO ROOM LIGHT
REMOVAL AND INSTALLATION
1. Disconnect the negative battery cable.
2. Remove in the sequence shown in the figure.
3. Install in the reverse order of removal.
76G14X-011
Sedan and Coupe/MX-6
License plate light
1. Screws
2. Lens
3. Bulb 5W x 2
Back up light
4. End trim
5. Bulb 21W
6. Nuts
7. Rear finisher
Hatchback
Corgo room light
1. Lens
2. Switch and bulb assembly 5W
License plate light
3. Side trim
4. Lower trim
5. End trim
6. Screws
7. Lens
8. Bulb 5W x 2
9. Rear finisher
14-35

1 4 INTERIOR
LIGHT AND
MAP LIGHT
INTERIOR LIGHT AND MAP LIGHT
REMOVAL AND INSTALLATION
1. Disconnect the negative battery cable.
2. Remove in the sequence shown in the figure.
3. Install in the reverse order of removal.
Map light
86U14X-082
Interior Light Map Light
1. Lens 1. Lens
2. Bulb 10W 2. Bulb 8W
14-36

MOLDING AND GARNISH 1 4
MOLDING AND GARNISH
STRUCTURAL VIEW
Coupe/MX-6
Sedan
76G14X-012
1. Windshield molding 6. Rear window lower molding 11. Rear window upper
2. Windshield lower molding 7. Rear window side molding molding
3. Drip molding 8. Bonnet molding 12. Center pillar garnish
4. Beltline molding 9. Front lower molding 13. Rear finisher
5. Quarter window molding 10. Trunk lid molding 14. Sail garnish
14—37

1 4 MOLDING AND GARNISH
WINDSHIELD MOLDING
Removal and Installation
1. Remove the windshield molding. (Refer to page
14-48)
2. Install the windshield molding. (Refer to page
14-51)
76G14X035
WINDSHIELD LOWER MOLDING
Removal and Installation
1. Remove the wiper arms.
2. Remove the lower molding screws and the lower
molding.
3. Install in the reverse order of removal.
86U14X-086
DRIP MOLDING
Removal and Installation
1. Insert a screwdriver between the roof rail and drip
molding and slightly loosen the end of the molding.
Note
Be careful not to scratch the molding.
2. Remove the molding by twisting upward with both
hands.
3. Install in the reverse order of removal.
86U14X-087
BELTLINE MOLDING
Removal and Installation
1. Remove the door mirror.
2. Remove the screw from the end of the beltline
molding, then pull the molding up to remove it.
3. Install in the reverse order of removal.
86U14X-088
14-38

MOLDING AND GARNISH 14
REAR WINDOW SIDE MOLDING (SEDAN)
Removal and Installation
1. Remove the rear side seatback bolt, then the rear
side seatback.
2. Remove the rear pillar trim.
3. Remove the window side molding nuts, then the
window side molding.
4. Install in the reverse order of removal.
86U14X-089
Vi
REAR WINDOW LOWER MOLDING
(SEDAN AND COUPE/MX-6)
Removal and Installation
1. Remove the rear window lower molding screws,
then the rear window lower molding.
2. Install in the reverse order of removal.
76G14X-013
REAR WINDOW UPPER MOLDING
(SEDAN, HATCHBACK AND COUPE/MX-6)
Removal and Installation
1. Remove the rear window side molding. (Refer to
page 14—54)
2. Remove the rear window upper molding.
3. Install in the reverse order of removal.
76G14X-014
BONNET MOLDING
(SEDAN AND HATCHBACK)
Removal and Installation
1. Remove the bonnet molding screws, then the bon-
net molding.
2. Install in the reverse order of removal.
76G14X-015
14-39